Universal Remote Control Universal Remote UR S86TVE User Manual

STEP2 Press [CH +] button.  
STEP2 Press [TV] and [MUTE] buttons simultaneously  
until the red light is on.  
Instructions  
This remote control is preprogrammed to operate  
CABLE Box. Please program it for your TV by  
following the instructions shown below.  
Operating Manual  
for 2 in 1 Cable TV  
Remote Control  
*Tip : Red light will blink twice.  
STEP3 Point the remote control toward the TV and  
enter the three-digit code from the code table. If there  
is more than one code number assigned to your TV  
brand, try one code number at a time until the TV  
turns off right after you entered the number.  
Searching Method  
Press [CH +] button and hold until the TV turns off. As  
soon as the TV turns off, release [CH+] button.  
The [POWER] button sends out the TV and CABLE  
power commands if you press the [POWER] button.  
To return to the original function, press the [CH-]  
button in the STEP2 .  
Batteries  
UR-S86TVE  
The remote control uses AAA batteries. Please be sure  
+
to match the batteries with the ( ) and (- ) markings  
B. Recalling the TV Three-digit code :  
inside the battery compartment during installation.  
STEP1 Press [ TV ] and [ MUTE ] buttons  
simultaneously until the red light is on.  
*Tip : You can confirm the power off and on by  
STEP2 Press [VOLUME -] button.  
pressing [MUTE] button.  
The red light will blink a number of times indicating the  
number of each digit of the code. Each digit is  
separated by one second interval of red light being off.  
STEP4 Press [TV] button to store the three-digit  
code.  
Install two AAA alkaline  
batteries as shown here  
*Tip : Red light will blink twice.  
*Tip : One blink, three blinks and 10 blinks,  
Three-digit code :  
indicates the code number 130.  
Set-up for your VOLUME control  
The remote control is preprogrammed to control  
VOLUME and MUTE functions through your TV. To  
switch VOLUME and MUTE functions to your Cable Box:  
Helpful hints  
Set-up for your Cable Box  
Press arrow gently &  
pull down to remove cover  
The remote control is preprogrammed to control  
your cable box. If it does not work properly, please  
set-up the right code by using the three-digit code  
or searching method.  
If you have a TV with a remote control, we  
recommend that you plug its power cord directly  
into a wall outlet if available (your cable installer  
may select an alternate setup)  
STEP1 Press [POWER] and [MUTE] buttons  
simultaneously until red light is on.  
Programming your remote control  
STEP2 Press [VOLUME +] button.  
Setup for your cable box  
STEP3 Press [POWER] button.  
To return to the TV’s VOLUME, press [TV] button.  
No setup is required. The remote control is  
preprogrammed to operate your cable box.  
*Tip : Red light will blink twice.  
Setup for your TV  
Operation  
Find your TV brand and its three-digit code on the  
back of this manual. If the TV brand is not listed,  
please use the Searching Method in STEP3 .  
Set-up for advanced functions  
A. To turn on your TV and Cable at the same time  
witPOWER button:  
If red light does not blink when you press keys the  
operation is intermittent:  
Universal Remote Control, Inc.  
Make sure the batteries are inserted correctly.  
Replace old batteries with two new AAA batteries.  
Please do not mix old batteries with new ones.  
STEP1 Turn on your TV manually.  
STEP1 Press [ POWER ] and [ 0 ] buttons simultaneously  
until the red light is on.  
OCE-0003E Rev 02(05/14/02)  
*Tip : If you have RCA TV, don’t turn on the TV.  
 

Taylor Scale 7322EXP User Manual
Teledex Answering Machine 3510 User Manual
Thule Automobile Accessories 018 User Manual
Timex Watch W 154 US User Manual
Toshiba Network Hardware GA 1170 User Manual
Vacuflo Vacuum Cleaner MAXUM 5 User Manual
ViewSonic Flat Panel Television CD5233 User Manual
ViewSonic Flat Panel Television ND4200 User Manual
Vivotek Security Camera FD6111 User Manual
Vulcan Hart Fryer 164BD User Manual