Hotpoint Clothes Dryer TVEL 75 User Manual

Instruction booklet  
TUMBLE DRYER  
Contents  
GB  
GB  
Important information, 2  
Product data, 2  
English  
Installation, 3-4  
Where to put your dryer  
Ventilation  
Electrical connection  
Levelling your dryer  
Before you start using your dryer  
Dryer description, 5  
The front  
The back  
Control panel  
Start and programmes, 6-10  
Choosing a programme  
Tables of Programmes  
The controls  
TVEL 75 Experience  
Laundry, 11-12  
Sorting your laundry  
Wash care labels  
Special clothing items  
Drying times  
Warnings and Suggestions, 13  
General safety  
Saving energy and respecting the environment  
Maintenance and Care, 14  
Switching off the electricity  
Cleaning the filter after each cycle  
Check the drum after each cycle  
Cleaning the dryer  
Troubleshooting, 15  
Service, 16  
Disposal  
Hotpoint Guarantee, 19  
Hotpoint After Sales Service, 20  
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and  
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the  
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.  
! Read these instructions carefully; the following pages contain important information on installation and suggestions  
on how the appliance works.  
This symbol reminds you to read this booklet.  
1
 
Installation  
Permanent venting  
Where to put your dryer  
GB  
In conjunction with the vent tube we recommend  
using a Wall/Window Vent Kit, available at a retail  
location or the nearest Spare Parts Dealer.  
Place your dryer at a distance from gas ranges,  
stoves, heaters, or cook tops because flames can  
damage the appliance.  
If you are going to install the  
Minimum gap 10mm  
Wall mounting  
appliance under a work  
1. Leave an opening in  
the wall to the left of the  
dryers proposed position.  
2. Keep the tube as short  
and straight as possible  
to prevent condensed  
moisture from backing up  
into the dryer.  
3. Similarly, the duct in  
the wall should slope  
downwards towards the  
outside.  
counter, be sure to leave a  
10mm space between the  
top and any other objects on  
or above the machine and a  
15mm space between the  
sides and lateral furnishings  
Minimum gaps  
15mm  
or walls. This is to ensure  
proper air circulation. Make sure that the back  
vents are not obstructed.  
Make sure you put your dryer in an environment  
that is not damp and has proper air circulation  
throughout, the dryer will not operate efficiently in  
an enclosed space or cupboard.  
Window mounting  
1. With a stacked dryer  
the hole in the window  
should ideally be made  
below the vent.  
! We do not recommend that the dryer is installed in a  
cupboard but the dryer must never be installed  
behind a lockable door, a sliding door or a door with a  
hinge on the opposite side to that of the dryer door.  
2. The tube should be  
kept as short as possible.  
Ventilation  
The Dryer dries your laundry by drawing in cool, clean  
and relatively dry air, heating it, and then distributing it  
through the clothes as they are gently tumbled. For  
optimum performance, the moist air is then blown out  
through a vent tube at the back of the dryer.  
When the dryer is in use, there has to be adequate  
ventilation to avoid the back flow of gases into the room  
from appliances burning other fuels, including open fires.  
Depending on how often you use your dryer, it is  
essential that areas A and B are checked periodically  
to remove lint or debris.  
The vent tube adaptor must be fitted securely thus  
preventing any humid air from being emitted back into  
the room.  
! The Dryer should not be pushed so far back that the  
tube adaptor is pulled out of position or the tube is  
squashed or bent.  
Mobile venting  
! The tube should be kept clear of the air intake vent  
and kinks or ‘U’ bends must be avoided as these will  
obstruct the tube or trap condensation.  
A vent tube must always be fitted when the dryer is  
used in conjunction with Mobile Venting.  
The tube must be fitted securely into the back of the  
dryer (see Dryer Description). If possible, it is always  
best to connect the tube to a permanent  
outlet close to the dryer. If permanent installation is  
not possible, the dryer will work just as well with the  
tube passing through a partly-opened window.  
! Ensure that the end of the tube is not directed  
toward the air intake vent at the rear of the dryer.  
! The vent tube should not exceed 2.4 metres in  
length and should be kept free of any possible  
accumulation of fluff, lint and water by shaking it out  
frequently. Always ensure that the tube is not  
squashed.  
3
 
Installation  
Open window venting  
Moulded plug  
GB  
The end of the tube  
! The plug must not be used  
without the fuse cover in place. If  
a replacement fuse holder/cover is  
required, it must be of the same  
colour coding or wording as  
shown on the base of the plug.  
Replacements are available from  
authorised dealers.  
should be directed  
downwards, to prevent  
warm moist air from  
condensing in the room or  
in the dryer.  
Changing the plug  
The wires in the power cord are coloured in accordance  
with the following:  
Green and Yellow  
(Earth) wire to terminal  
! Ensure that the dryer is adequately ventilated and  
that the end of the vent tube is not directed towards  
the air intake duct.  
marked ‘E’, symbol  
or coloured green and  
yellow.  
,
! The vent tube must always be fitted for optimum  
performance.  
! Make sure that the vent tube and air intake vents are  
not obstructed or blocked.  
! The dryer must not recycle exhaust air.  
! Misusing a tumble dryer may create a fire hazard.  
! Do not discharge exhaust air into a flue which is  
used for exhaust fumes from other appliances that  
burn gas or other fuels.  
! Do not discharge exhaust air into an extraction  
system or any duct with an extractor fan. This will  
affect the way the thermal controls operate and can  
result in a fire hazard.  
13A ASTA approved  
fuse to BS1362.  
Blue (Neutral) wire to  
terminal marked ‘N’ or  
coloured black.  
Brown (Live) wire to  
terminal marked ‘L’ or  
coloured red.  
Cord clamp  
! If the plug being replaced is a non-rewirable type,  
then the cut-off plug must be disposed of safely. DO  
NOT leave it where it can be inserted into a socket  
and create a shock hazard.  
! The power supply cord should be checked periodically  
and replaced by a cord specially prepared for this  
dryer and fitted only by authorised technicians (see  
Service). New or longer power cords are supplied at  
an extra charge by authorised dealers.  
Electrical connections  
! The manufacturer denies any responsibility should  
any of these rules not be followed.  
! If in doubt about any of the above consult a qualified  
electrician.  
Make sure of the following before you insert the plug  
into the the electrical socket:  
The socket must be grounded.  
The socket must be able to sustain the machines  
maximum power, which is indicated on the rating  
label (see Dryer Description).  
Levelling your dryer  
The dryer must be installed level for correct operation.  
When you have installed your  
dryer in its final location check  
that it is level first side to side,  
then front to back.  
Power voltage must be within the values indicated  
on the rating label (see Dryer Description).  
The socket must be compatible with the dryers  
plug. Should this not be the case, replace the  
plug or the socket.  
! The dryer must not be installed outdoors, even if the  
space is sheltered. It can be very dangerous if it is  
exposed to rain or storms.  
! Once installed, the dryers electrical wire and plug  
must be within easy reach.  
If the dryer is not level, use a  
wooden block to  
support it while adjusting the two  
front legs up or down, until your  
dryer is level.  
! Do not use extension cords.  
! The power cord must not be bent or squashed.  
! The power cord supplied is fitted with a BS1363 plug  
and a 13 amp BS1362 fuse. If you need to replace the  
fuse, use only those rated at 13 amp (13A) and ASTA  
approved to BS1362.  
Before you start using your dryer  
Once you have installed your dryer and before you  
use it, clean the inside of the drum to remove any dust  
that could have accumulated during transport.  
4
 
Dryer Description  
The front  
The back  
GB  
Drum  
Model & Serial numbers  
Control Panel  
Air Intake Vent  
Rating plate  
Vent Tube fitted here  
Filter  
Caution: Hot!  
Control panel  
PROGRAMMES  
Knob  
START/PAUSE  
Button & Light  
Clean Filter  
Light  
Indicator  
OPTION  
Buttons & Lights  
ON/OFF  
Button  
Progress or Delay  
Lights  
button in pauses the programme and stops the dryer.  
The light is green when programme is running, flashing  
amber if the programme has been paused or flashing  
green if on standby waiting to start a programme (see  
Start and Programmes).  
Note: This light also flashes amber during the Post  
Care phase of a programme.  
The ON/OFF button  
: If the dryer is running and  
this button is pressed and held for more than 3  
seconds, the dryer is turned off. Press and hold again  
for more than 3 seconds and the dryer reactivates.  
The PROGRAMMES knob sets the programme: rotate  
it until the indicator is pointing to the programme you want  
to select (see Start and Programmes).  
The Progress or Delay lights show you the status of  
the programme, or the delay time when they flash.  
During a delayed start the lights flash to show the  
delay selected. When (not flashing) they show each  
stage of the programme by the corresponding light  
turning on (see Start and Programmes).  
The OPTION buttons/lights select available options for  
your selected programme. The lights indicate that the  
option has been selected. If an option is not available  
the buzzer will beep three times (see Start and  
Programmes).  
The Clean Filter light gives you a reminder before  
every programme that it is essential to clean the filter  
every time the dryer is used (see Maintenance and Care).  
The START/PAUSE button/light  
starts a selected  
programme. When you press this button there will be  
one beep and the progress lights will flash to confirm  
the action. When a programme is running, holding this  
5
 
Start and Programmes  
Choosing a programme  
while others continue drying. When you close  
the door again, press the START/PAUSE button in  
order to resume drying.  
(When the door is opened the START/PAUSE light  
will flash Amber, after the door is closed and the  
START/PAUSE button pressed, the START/PAUSE  
light will stop flashing and show green.)  
Note: During the Post Care phase this light  
flashes Amber.  
GB  
1. Plug the dryer into the electrical socket.  
2. Sort your laundry according to fabric type (see  
Laundry).  
3. Open the door and make sure the filter is clean  
and in place (see Maintenance).  
4. Load the machine and make sure items are not in  
the way of the door seal. Close the door.  
5. If none of the lights are on: Press the ON/OFF  
9. At the end of the drying cycle the End light comes  
on and either :  
button  
.
6. Choose a programme by checking the Programmes  
Guide (see Programmes) as well as the indications  
for each type of fabric (see Laundry).  
- The buzzer will beep 3 times to let you know  
that your programme is complete. (Note: If  
the SOUND option was selected the buzzer  
beeps 3 times every 30 seconds for 5  
minutes).  
- Select a programme by rotating the  
PROGRAMMES knob.  
7. Set a delay time and other options if necessary.  
8. The START/PAUSE light is flashing green:  
or - If you have selected the Crease Care option  
and you do not take the items out immediately,  
the items will tumble occasionally for 10  
hours or until you open the door, the buzzer  
will then beep 3 times to confirm the  
programme is completed.  
- press the START/PAUSE  
button to begin.  
The green light stops flashing.  
During the drying programme, you can check on  
your laundry and take out items that are dry  
10. Open the door, take the laundry out, clean the filter  
and replace it (see Maintenance).  
11. Unplug the dryer.  
Note:  
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is detected. Press the ON/OFF button briefly and wait for the  
dryer to reactivate.  
Shirts Light Dry  
High heat option  
This is a programme for shirts made from cotton.  
It can be used for load sizes up to 3kg (approximately 10 shirts).  
This programme will take about 60 minutes, but may take longer depending on the size of the load and the spin  
speed used in your washer.  
Low heat option  
This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such  
as polyester and cotton.  
It can be used for load sizes up to 3kg (approximately 14 shirts).  
This programme will take about 55 minutes, but may take longer depending on the size of the load and the spin  
speed used in your washer.  
Shirts dried using this programme are usually ready to put away, the edges or seams may be slightly damp. If this is  
the case, try turning the shirts inside out and running the programme again for a short period.  
Jeans  
This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.  
It can be used for load sizes up to 3kg (approximately 4 pairs).  
Do not mix dark and light coloured items.  
It can also be used on other garments made from the same material, such as jackets.  
This programme will take about 85 minutes, but may take longer depending on the size of the load and the spin  
speed used in your washer.  
Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is  
the case, try turning the jeans inside out and running the programme again for a short period.  
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.  
6
 
Start and Programmes  
Wool Programme  
GB  
This is a programme for tumble dryer safe garments marked with the symbol  
It can be used for load sizes up to 1kg (approximately 3 sweaters).  
We recommend that garments are turned inside out before drying.  
This programme will take about 60 minutes, but may take longer depending on the size and density of the load and the  
spin speed used in your washer.  
.
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly  
damp. Allow these to dry naturally as over-drying could damage garments.  
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.  
! This programme is not suitable for Acrylic garments.  
Baby Delicate Programme  
This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)  
and for drying your delicate clothes.  
DO NOT dry items such as bibs and nappy pants with plastic coverings.  
It can be used for load sizes up to 2kg.  
This programme will take about 60 minutes, but may take longer depending on the size and density of the load  
and the spin speed used in your washer.  
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be  
slightly damp. If this is the case, try turning items inside out and running the programme again for a short period.  
Bed & Bath  
This is a programme for Cotton Towels and sheets.  
It can be used on any load size, do not overload your dryer (see Laundry).  
This programme will take about 100 minutes, but may take longer depending on the the size and density of the  
load and the spin speed used in your washer.  
Loads dried using this programme are usually ready to use, the edges or seams may be slightly damp, especially  
on large items. If this is the case, try opening them out and running the programme again for a short period.  
Heat & Enjoy  
This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for  
warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature) and runs at this  
temperature for a maximum of 4 hours or until you stop the cycle by opening the door.  
Maximum load 3kg.  
Easy Iron Programme  
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which  
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle  
relaxes the fibres and makes them easier to iron and fold.  
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.  
For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:  
Fabric  
Maximum load  
2.5kg  
2kg  
Cotton and Cotton mixtures  
Synthetics  
Denim  
2kg  
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles  
and put them away in the closet. Should this not be possible repeat the programme.  
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,  
and less well on acrylic fibres and on materials such as Tencel®.  
Refresh  
! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.  
It can be used on any load size, but is more effective on smaller loads.  
Do not overload your dryer (see Laundry).  
This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.  
7
 
Start and Programmes  
Programmes  
! If none of the lights are lit; Press the ON/OFF button  
GB  
and then select programme.  
What it does...  
How to set it...  
Notes/Options available:  
Programme  
Dries your clothes, ready 1. Position the PROGRAMME knob on 1.  
Delay Timer  
Crease Care or Sound  
1
Cottons  
Ready to wear  
for wearing.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
.
Delay Timer  
High Heat  
Crease Care or Sound  
Dries your clothes, ready 1. Position the PROGRAMME knob on 2.  
2
Cottons  
Cupboard Dry  
for putting away.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
.
Delay Timer  
High Heat  
Crease Care or Sound  
Dries your clothes, ready 1. Position the PROGRAMME knob on 3.  
3
Cottons  
Hanger Dry  
for hanging.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
.
Delay Timer  
High Heat  
Crease Care or Sound  
Dries your clothes, ready  
for ironing.  
1. Position the PROGRAMME knob on 4.  
2. Select any Options, if required.  
4
Cottons  
Iron Dry  
3. Press the Start/Pause button  
.
Dries your Cotton or  
Synthetic shirts, ready for  
putting away.  
Delay Timer  
High Heat  
Crease Care or Sound  
1. Position the PROGRAMME knob on 5.  
2. Select any Options, if required.  
5
Shirts  
Light Dry  
3. Press the Start/Pause button  
.
Dries your Synthetic  
clothes, ready for putting  
away.  
Delay Timer  
Crease Care or Sound  
1. Position the PROGRAMME knob on 6.  
2. Select any Options, if required.  
6
Synthetics  
3. Press the Start/Pause button  
.
8
 
Start and Programmes  
Programmes Table  
! If none of the lights are on; Press the ON/OFF button  
GB  
and then select programme.  
EXCLUSIVES  
Programme  
What it does...  
Dries your Cotton  
Jeans.  
How to set it...  
Notes/Options available:  
Delay Timer  
Crease Care or Sound  
1. Position the PROGRAMME knob on 7.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
7
Jeans  
1. Position the PROGRAMME knob on 8.  
2. Press the Start/Pause button  
Dries your Woollen  
clothes, (see previous  
pages).  
Sound  
8
Wool  
Dries your clothes on  
Low heat setting, ready  
to be worn.  
1. Position the PROGRAMME knob on 9.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
Delay Timer  
Crease Care or Sound  
9
Baby  
Delicates  
1. Position the PROGRAMME knob on 10.  
2. Select any Options, if required.  
3. Press the Start/Pause button  
Dries your Bedding &  
Towels on High Heat  
setting, ready for putting  
away.  
Delay Timer  
Crease Care or Sound  
10  
Bed & Bath  
TIMED DRY  
Programme  
Notes/Options available:  
What it does...  
How to set it...  
Always use timed drying 1. Position the PROGRAMME knob on either  
Timed  
Drying  
Delay Timer  
High Heat  
Crease Care or Sound  
11. for 30 minute programme  
for loads of less than  
1kg.  
The heat setting used  
depends on the fabric  
that is being dried (see  
laundry).  
or  
12. for 60 minute programme  
or  
13. for 140 minute programme  
The last 10 minutes of  
or  
these programmes is the  
cool tumble phase  
2. Select any Options, if required.  
3. Press the Start/Pause button  
EXTRA  
Programme  
What it does...  
Warms towels,  
bathrobes or other  
clothes  
How to set it...  
1. Position the PROGRAMME knob on 14.  
2. Press the Start/Pause button  
Notes/Options available:  
None  
14  
Heat & Enjoy  
Brief programme  
1. Position the PROGRAMME knob on 15.  
2. Press the Start/Pause button  
Sound  
15  
Easy Iron  
(approximately 10  
minutes) that softens  
fibres of clothing that is  
ready for ironing.  
! This is not a drying  
programme (see previous  
pages).  
20-minute programme  
that airs your clothes  
with cool air. Use also to  
cool warm clothes.  
1. Position the PROGRAMME knob on 16.  
2. Press the Start/Pause button  
Sound  
16  
Refresh  
9
 
Start and Programmes  
The Controls  
High Heat  
GB  
Press this button and a high heat setting is selected and  
the light next to the button comes on. If the light  
alongside the button is on then pressing the button  
selects a low heat setting and the light goes out.  
Not all programmes allow you to change this setting.  
PROGRAMMES knob  
! Warning, if after pressing the start button, the  
programmes knob position is changed, the new position  
will NOT change the programme selected.  
To change a selected programme, press the  
Sound  
Start/Pause button  
, the light flashes Amber to  
If selected, gives a signal at the end of the drying cycle,  
to remind you that the clothes are ready to be removed.  
Not available with the Heat & Enjoy programme.  
Note: If you have selected the Crease Care option this  
option is not available.  
indicate the programme is paused. Select the new  
programme and any options required, the light will  
then flash green. Press the Start/Pause button  
again and the new programme will start.  
OPTION buttons / lights  
These buttons are used to customise the selected  
programme to your requirements. Not all options are  
available for all programmes (see Start and  
Programmes). If an option is not available and you  
press the button, the buzzer will beep three times. If  
the option is available the option light next to the  
button lights to confirm the selection.  
Door Opening  
Opening the door (or pressing the Start/Pause button)  
during a programme will stop the dryer and have the  
following effects:  
Note: The Start/Pause light flashes Amber during the  
Post Care phase of a programme.  
The Start/Pause light flashes Amber.  
During a delay phase the delay will continue to  
Progress (  
Drying, Cool Tumble, End) /  
count down. The Start/Pause button must be  
pressed to resume the delay programme.  
One of the delay lights will flash to show the  
current delay setting.  
Delay (3hr 6hr 9hr) Lights  
When the light next to the delay button is on, these lights  
flash to indicate the delay time selected. During other  
programmes they indicate the progress of the dryer,  
each one comes on as the corresponding phase starts.  
The Start/Pause button must be pressed to  
resume the programme. The progress lights will  
change to show the current status and the  
Start/Pause light will stop flashing and turn green.  
Delay Timer (Time Delay)  
The start of some programmes (see Start and  
Programmes) can be delayed for up to 9 hours in 3hr  
steps.  
During the Post Care phase of a drying  
programme, the programme will finish. Pressing  
the Start/Pause button will re-start a new  
programme at the beginning.  
When a delayed start is in progress the light next to the  
delay button will be on and the selected delay period  
light will flash (after the start button has been pressed).  
To set a delayed start, press the Delay Timer button,  
and the light next to the button will come on together  
with the 3hr delay light. Pressing the button again will  
advance the delay setting to 6hr, the 3hr light goes  
out and the 6hr light is on. Each time you press the  
button the delay setting advances 3 hours, as indicated  
by the corresponding light. If the 9hr light is on,  
pressing the button again will cancel the delay.  
Holding in the On/Off button will also cancel.  
Crease Care  
The pre-care option is only available if a delayed start has  
been selected. It tumbles the clothes occasionally during  
the delayed period to help prevent creases developing.  
The post-care option occasionally tumbles the clothes  
after the end of the drying and cool tumble cycles to  
prevent creases developing, should you not be available  
to remove the load immediately the programme is  
complete. The End light is on during this phase. Note:  
The Start/Pause light flashes Amber during this phase.  
Selecting this option enables both the pre and post care  
functions if appropriate.  
Changing the programmes knob will select a new  
programme and the Start/Pause light will flash  
green. You can use this to select the Refresh  
programme to cool the clothes, if you find them  
dry enough. Press the Start/Pause button to begin  
a new programme.  
Note  
If you have a power cut, switch off the power or  
remove the plug, press and hold the On/Off button  
until the dryer reactivates, then press the Start/Pause  
button.  
Note: If you have selected the Sound option this option is  
not available.  
10  
 
Laundry  
Sorting your laundry  
Wash Care Labels  
GB  
Check symbols on clothing labels to make sure  
that the articles can be tumble dried.  
Sort laundry by fabric type.  
Empty pockets and check buttons.  
Close zippers and hooks and tie loose belts and  
strings.  
Wring out each item in order to eliminate as much  
excess water as possible.  
Look at the labels on your garments, especially when  
tumble drying for the first time. The following symbols  
are the most common:  
May be tumble dried  
Do not tumble dry  
! Do not load dripping wet clothes into the dryer.  
Tumble dry at high heat setting  
Tumble dry at low heat setting  
Maximum load size  
Do not load more than maximum capacity.  
These numbers refer to dry weight:  
Natural fibres: 7kg max (15lb)  
Synthetic fibres: 3kg max (6.6lb)  
Items not suitable for tumble drying  
Articles that containing rubber or rubber-like  
materials or plastic film (pillows, cushions, or PVC  
rainwear), any other flammable articles or objects  
that contain flammable substances (towels soiled  
with hair spray).  
Glass fibres (certain types of draperies)  
Items which have been dry cleaned  
! DO NOT overload the dryer as this could result in  
reduced drying performance.  
Typical weights  
Note: 1kg = 1000g  
(1lb = 16oz)  
150g  
Items with the ITCL Code  
(see Special  
Clothes  
clothing items). These can be cleaned with special  
at-home dry cleaning products. Follow instructions  
carefully.  
Large bulky items (quilts, sleeping bags, pillows,  
cushions, large bedspreads etc). These expand  
when drying and would prevent airflow through  
the dryer.  
Blouse  
Cotton  
(5oz)  
Other  
Cotton  
Other  
100g  
500g  
350g  
700g  
(3oz)  
Dress  
(1lb 2oz)  
(12oz)  
(1lb 6oz)  
Jeans  
10 nappies  
Shirt  
1000g (2lb 3oz)  
Cotton  
Other  
300g  
200g  
125g  
(10oz)  
(7oz)  
(4oz)  
T-Shirt  
Household Items  
Duvet cover  
(Double)  
Cotton  
Other  
1500g (3lb 5oz)  
1000g (2lb 3oz)  
Large Tablecloth  
Small Tablecloth  
Tea Towel  
700g  
250g  
100g  
700g  
350g  
500g  
350g  
(1lb 6oz)  
(9oz)  
(3oz)  
Bath Towel  
(1lb 6oz)  
(12oz)  
Hand Towel  
Double Sheet  
Single Sheet  
(1lb 2oz)  
(12oz)  
At the end of a drying cycle, cottons could still be  
damp if you grouped cottons and synthetics together.  
If this happens simply give them an additional short  
period of drying.  
11  
 
Laundry  
Special clothing items  
Times are approximate and can vary depending  
upon:  
GB  
Blankets and Bedspreads: acrylic items (Acilan,  
Courtelle, Orion, Dralon) must be dried with special  
care on LOW heat setting. Avoid drying for a long  
period of time.  
Amount of water retained in clothes after spin  
cycle: towels and delicates retain a lot of water.  
Fabrics: items that are the same type of fabric but  
Pleated or creased garments: read the manufacturer’s  
drying instructions on the garment.  
different textures and thicknesses may not have  
the same drying time.  
Starched articles: do not dry these with non-starched  
items. Make sure that as much of the starch solution is  
removed from the load as possible before placing it in  
the dryer. Do not over-dry: the starch will become  
powdery and leave your clothing limp, which defeats  
the purpose of starch.  
Quantity of laundry: single items or small loads  
may take longer to dry.  
Dryness: If you are going to iron some of your  
clothes, they can be taken out while still a bit  
damp. Others can be left longer if you need them  
to be completely dry.  
Heat setting.  
Drying times  
Room temperature: if the room where the dryer is  
The table below presents APPROXIMATE drying times  
in minutes. Weights refer to dry garments:  
located is cold, it will take longer for the dryer to  
dry your clothes.  
Bulk: some bulky items can be tumble dried with  
Cottons  
care. We suggest that you remove these items  
several times, shake them out, and return them to  
the dryer until finished.  
Full Heat (use High Heat option for Timed Drying)  
Drying times 800-1000rpm in washing machine  
1kg 2kg 3kg  
4kg  
5kg  
6kg  
7kg  
! Do not over-dry your clothes.  
All fabrics contain a little natural moisture, which  
20-30 35-45 45-60 60-70 70-80 80-100 90-120  
keeps them soft and fluffy.  
Synthetics  
Full Heat (use High Heat option for Timed Drying)  
Drying times on reduced spin in washing machine  
1kg  
2kg  
3kg  
20-40  
30-50  
40-70  
Delicates (e.g.Acrylics)  
Use Timed Drying with Low Heat option  
Drying times on reduced spin in washing machine  
1kg  
30  
2kg  
60  
12  
 
Warnings and Suggestions  
To minimise the risk of fire in your tumble dryer, the  
! The appliance has been designed and built according  
to international safety standards.  
These warnings are given for safety reasons and must  
be followed carefully.  
GB  
following should be observed:  
Tumble dry items only if they have been washed with  
detergent and water, rinsed and been through the spin  
cycle. It is a fire hazard to dry items that HAVE NOT  
been washed with water.  
Do not dry garments that have been treated with  
General safety  
chemical products.  
Do not tumble dry items that have been spotted or  
This tumble dryer is not intended for use by  
soaked with vegetable or cooking oils, this constitutes a  
fire hazard. Oil-affected items can ignite spontaneously,  
especially when exposed to heat sources such as a tumble  
dryer. The items become warm, causing an oxidisation  
reaction with the oil, Oxidisation creates heat. If the heat  
cannot escape, items can become hot enough to catch  
fire. Piling, stacking or storing oil-effected items can prevent  
heat from escaping and so create a fire hazard.  
If it is unavoidable that fabrics containing vegetable or  
cooking oil or those that have been contaminated with  
hair care products be placed in a tumble dryer they should  
first be washed with extra detergent - this will reduce, but  
not eliminate the hazard. The cool tumble phase should  
be used to reduce the temperature of the items. They  
should not be removed from the dryer and piled or  
stacked while hot.  
persons (including children) with reduced physical,  
sensory or mental capabilities, or lack of experience  
and knowledge, unless they have been given  
supervision or instruction concerning use of the  
appliance by a person responsible for their safety.  
This tumble dryer has been designed for home,  
and not professional use.  
Do not touch the appliance while barefoot or with  
wet hands or feet.  
Unplug the machine by pulling on the plug, not  
the cord.  
Children must not be in proximity of the dryer  
when in use. After using the dryer, turn it off and  
unplug it. Keep the door closed to make sure that  
children do not use it as a toy.  
Children should be supervised to ensure that they  
do not play with the dryer.  
The appliance must be installed correctly and  
have proper ventilation. The air intake vents  
behind the machine, the outlet vents and the vent  
tube should never be obstructed (see Installation).  
Never direct the vent tube outlet towards the air  
intake at the back of the machine.  
Never allow the tumble dryer to recycle exhaust air.  
Never use the dryer on carpeting where the pile  
height would prevent air from entering the dryer  
from the base.  
Check to see if the dryer is empty before loading it.  
The back of the dryer could become very  
hot. Never touch it while in use.  
Do not use the dryer unless the filter is securely  
in place (see Maintenance).  
Do not overload the dryer (see Laundry) for  
maximum loads.  
Do not load items that are dripping wet.  
Carefully check all instructions on clothing labels  
(see Laundry).  
Do not tumble dry items that have previously been  
cleaned in or washed in, soaked in or soiled with  
petrol/gasoline, dry cleaning solvents or other flammable  
or explosive substances. Highly flammable substances  
commonly used in domestic environments including  
cooking oil, acetone, denatured alcohol, kerosene, spot  
removers, turpentine, waxes and wax removers. Ensure  
these items have been washed in hot water with an extra  
amount of detergent before being dried in the tumble dryer.  
Do not tumble dry items containing foam rubber (also  
known as latex foam), or similarly textured rubber like  
materials. Foam rubber materials can, when heated,  
produce fire by spontaneous combustion.  
Fabric softener or similar products should not be used in  
a tumble dryer to eliminate the effects of static electricity  
unless the practice is specifically recommended by the  
manufacturer of the fabric softener product.  
Do not tumble dry undergarments that contain metal  
reinforcements eg. bras with metal reinforcing wires.  
Damage to the tumble dryer can result if the metal  
reinforcements come loose during drying.  
Do not tumble dry rubber, plastic articles such as shower  
caps or babies waterproof covers, polythene or paper.  
Do not tumble dry rubber backed articles, clothes fitted  
with foam rubber pads, pillows, galoshes and rubber  
coated tennis shoes.  
Do not tumble dry large, very bulky items.  
Do not tumble dry acrylic fibres at high temperatures.  
Complete each programme with its Cool Tumble Phase.  
Do not turn off the dryer when there are still warm  
items inside.  
Clean the filter after each use (see Maintenance).  
Do not allow lint to collect around the dryer.  
Never climb on top of the dryer. It could result in  
damage.  
Always follow electrical standards and requirements  
(see Installation).  
Always buy original spare parts and accessories  
(see Service).  
Remove all objects from pockets, especially lighters  
(risk of explosion).  
! WARNING: Never stop the dryer before the end of the  
drying cycle unless all items are quickly removed and  
spread out so that the heat is dissipated.!  
Saving energy and respecting the  
environment  
Wring out items to eliminate excess water before  
tumble drying (if you use a washing machine first,  
select a high spin cycle). Doing this will save time  
and energy during drying.  
Always dry full loads - you save energy: single  
items or small loads take longer to dry.  
Clean the filter after each use to contain energy  
consumption costs (see Maintenance).  
13  
 
Maintenance and Care  
Switching off the electricity  
Check the drum after each cycle  
GB  
Unplug your dryer when not using it, when cleaning it  
and during all maintenance operations.  
Turn the drum manually in order to remove small items  
(handkerchiefs) that could have been left behind.  
Cleaning the drum  
Clean the filter after each cycle  
! Do not use abrasives, steel wool or stainless steel  
The filter is an important part of your dryer:  
cleaning agents to clean the drum.  
it accumulates lint and fluff that is formed while drying.  
Small items could also become trapped in the filter.  
When finished drying, therefore, clean the filter by  
rinsing it under running water or with your vacuum  
cleaner. Should the filter become clogged up, the airflow  
inside the dryer will be seriously compromised: drying  
times lengthen and you will consume more energy. It  
may also damage your dryer.  
A coloured film may start to appear on the stainless  
steel drum, this may be caused by a combination of  
water and, or cleaning agents such as fabric conditioner  
from the wash. This coloured film will not affect the  
dryer performance.  
Cleaning  
The filter is found in front  
of the dryer trim  
External parts in metal or plastic and rubber parts  
(see diagram).  
can be cleaned with a damp cloth.  
Periodically check the vent tube and any  
permanent venting fixture to make sure that there  
has been no accumulation of fluff or lint, and  
remove it.  
Remove lint that collects around the filter and the  
outlet vents.  
Removing the filter:  
1. Pull the plastic grip of  
the filter upwards (see  
diagram).  
! Do not use solvents or abrasives.  
! Your dryer uses special bearing components which  
do not need lubrication.  
! Have your dryer checked regularly by authorised  
technicians to ensure electrical and mechanical safety  
(see Service).  
2. Open the filter and clean the lint from  
the inside.  
3. Replace it correctly. Ensure the filter is fully located  
flush into the tumble dryer trim.  
4. Remove any lint that has built up on the inside of the  
door and around the door seal.  
! Do not use the dryer without replacing the filter.  
14  
 
Troubleshooting  
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the  
following troubleshooting suggestions:  
GB  
Problem:  
Possible causes / Solution:  
The tumble dryer won’t start.  
The plug is not plugged into the socket, or not making contact.  
There has been a power failure.  
The fuse has blown. Try to plug another appliance into the socket.  
You are using an extension cord? Try to plug the dryer’s power cord  
directly into the socket.  
The door is not closed securely?  
The PROGRAMMES knob has not been set properly (see Start and  
Programmes).  
The START/PAUSE button has not been pressed (see Start and  
Programmes).  
Drying cycle will not begin.  
Its taking a long time to dry.  
You have set a delayed time (see Start and Programmes).  
The filter has not been cleaned (see Maintenance).  
The correct programme has not been selected for the type of fabric you  
are drying (see Start and Programmes).  
The flexible vent tube is obstructed (see Installation).  
The air intake vent is obstructed (see Installation).  
The permanent ventilation flap on the storm cover is obstructed (see  
Installation).  
The items were too wet (see Laundry).  
The dryer was overloaded (see Laundry).  
Programme finishes and  
clothes are damper than  
expected.  
! For safety the dryer has a maximum programme time of 3 hours. If an  
automatic programme has not sensed the required final moisture in this time  
the dryer will complete the programme and stop. Check the above points  
and run the programme again, if the results are still damp, contact the  
Service Centre (see Service).  
The START/PAUSE light  
flashes amber and all Option  
lights also flash to indicate a  
fault.  
Try turning the dryer off and remove the plug. Then replace the plug and  
turn on, if a fault is still shown when you turn the dryer back on: note the  
lights that are on (not flashing) and contact the Service Centre (see  
Service).  
15  
 
Service  
Before calling the Service Centre:  
Spare Parts  
GB  
Use the troubleshooting guide to see if you can  
solve the problem yourself (see Troubleshooting).  
If not, turn off the dryer and call the Service Centre  
closest to you.  
This dryer is a complex machine. Repairing it yourself  
or having a non-authorised person try to repair it could  
cause harm to one or more persons, could damage  
the machine and could invalidate the spare parts  
warranty.  
What to tell the Service Centre:  
Call an authorised technician if you experience problems  
while using the machine.  
name, address and post code.  
telephone number.  
the type of problem.  
the date of purchase.  
the appliance model (Mod.).  
the serial number (S/N).  
This information can be found on the data label inside  
the door of the machine.  
Recycling and Disposal Information  
As part of our continued commitment to helping  
the environment, we reserve the right to use  
quality recycled components to keep down customer  
costs and minimise material wastage.  
Disposal of old electrical appliances  
The European Directive 2002/96/EC on Waste Electrical  
and Electronic Equipment (WEEE), requires that old  
household electrical appliances must not be disposed  
of in the normal unsorted municipal waste stream. Old  
appliances must be collected separately in order to  
optimise the recovery and recycling of the materials  
they contain and reduce the impact on human health  
and the environment.  
Disposing of the packaging material: follow local  
regulations, so the packaging can be recycled.  
To minimise risk of injury to children, remove the  
door and plug - then cut off mains cable, flush  
with the appliance. Dispose of these parts separately  
to ensure that the appliance can no longer be  
plugged into a mains socket.  
The crossed out “wheeled bin” symbol on the  
product reminds you of your obligation, that  
when you dispose of the appliance it must be  
separately collected.  
Consumers should contact their local authority or  
retailer for information concerning the correct disposal  
of their old appliance.  
This appliance conforms to the following EC Directives:  
- 2006/95/EC (Low Voltage Equipment)  
- 2004/108/EC (Electromagnetic Compatibility)  
16  
 
GB  
17  
 
18  
 
Guarantee  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturers’ guarantee, which covers the cost of  
breakdown repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be  
defective because of either workmanship or materials, we will, at our discretion, either  
repair or replace the appliance at no cost to you.  
The guarantee is subject to the following conditions:  
- The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
- The appliance is only used on the electricity or gas supply printed on the rating plate.  
- The appliance has been used for normal domestic purposes only.  
- The appliance has not been altered, serviced, maintained, dismantled or otherwise  
interfered with by any person not authorised by us.  
- Any repair work must be undertaken by us or our appointed agent.  
- Any parts removed during repair work or any appliance that is replaced become our  
property.  
- The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
- Damage resulting from transportation, improper use, neglect or interference or as a  
result of improper installation.  
- Replacement of any consumable item or accessory. These include but are not limited to:  
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
- Replacement of any removable parts made of glass or plastic.  
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN  
COMMERCIAL OR NON-DOMESTIC PREMISES.  
Non-Domestic Usage Policy:  
Indesit Company manufactures appliances for domestic use only. We understand that in  
some cases our appliances are used in commercial and/or non-domestic situations. We  
still provide a full 12 month manufacturers’ guarantee, provided the appliance has not been:  
Accidentally damaged - Damage that occurs suddenly as a result of an unexpected and  
non-deliberate external action.  
Maliciously damaged - The deliberate and intentional damage to the product.  
Subjected to misuse - Incorrect or careless or improper use.  
Subjected to overuse - Excessive usage versus that expected of a domestically situated  
appliance.  
5 Year Parts Guarantee  
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is  
conditional on you registering your appliance with us and the parts being fitted by one  
of our authorised engineers. There will be a charge for our engineer’s time.  
To activate the extra parts warranty on your appliance, simply call our free phone registration line on  
0800 519 2102 (Republic of Ireland 1800 844 347)  
19  
 
195100543. 03 N  
.
10/2012 - LION fpg Four Ashes, Wolverhampton  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense  
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on  
UK: 08448 226 226  
Republic of Ireland: 01 230 0233  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint  
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance,  
or, where necessary, to arrange for an engineer to call.  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its  
working life than us - the manufacturer.  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in the country offering you access to 400 skilled  
telephone advisors and 1100 fully qualified engineers on call to ensure you receive  
fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number  
Serial number  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that  
protect and hygienically clean your appliance to keep it looking good and functioning  
efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership.  
To activate your FREE 5 year parts guarantee you must register your appliance with us.  
Free phone UK: 0800 519 2102  
Republic of Ireland: 1800 844 347  
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB  
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17  
 

Graco Inc Power Roller 244512 User Manual
Greenheck Fan Smoke Alarm SSFSDR 511 User Manual
Grizzly Bread Maker H5383 User Manual
Grizzly Grinder T23083 User Manual
Grundig Radio MINI400 User Manual
Harman Kardon Stereo Receiver AVR 240 User Manual
Hasbro Games 10437 User Manual
Honeywell Ventilation Hood W8150 User Manual
Hunter Fan Fan 20552 User Manual
Husqvarna Brush Cutter 3325 User Manual