Grizzly Staple Gun G6043 User Manual

18 GAUGE STAPLER KIT  
MODEL G6042/3  
INSTRUCTION MANUAL  
Model G6042  
Model G6043  
COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN TAIWAN  
 
Safety Instructions For Power Tools  
10. USE PROPER EXTENSION CORD  
15. MAINTAIN TOOLS WITH CARE.  
Keep tools sharp and clean for best  
and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
for the tool. Make sure your extension  
cord is in good condition. Conductor  
size should be in accordance with the  
chart below. The amperage rating  
should be listed on the motor or tool  
nameplate. An undersized cord will  
cause a drop in line voltage resulting  
in loss of power and overheating.  
Your extension cord must also con-  
tain a ground wire and plug pin.  
Always repair or replace extension  
cords if they become damaged.  
16. DISCONNECT TOOLS before ser-  
vicing and changing accessories.  
17. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Make sure  
switch is in off position before plug-  
ging in.  
18. USE  
THE  
RECOMMENDED  
Consult the  
ACCESSORIES.  
owner’s manual for recommended  
accessories. The use of improper  
accessories may cause risk of injury.  
Minimum Gauge for Extension Cords  
AMP  
RATING  
0-6  
LENGTH  
50ft  
16  
25ft  
18  
18  
16  
14  
12  
10  
100ft  
16  
14  
14  
12  
19. CHECK DAMAGED PARTS. Before  
further use of the tool, a guard or  
other part that is damaged should be  
carefully checked to determine that it  
will operate properly and perform its  
intended function. Check for align-  
ment of moving parts, binding of  
moving parts, breakage of parts,  
mounting, and any other conditions  
that may affect its operation. A guard  
or other part that is damaged should  
be properly repaired or replaced.  
7-10  
16  
16  
12  
12  
11-12  
13-16  
17-20  
21-30  
10  
No  
10  
11. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neckties,  
rings, bracelets, or other jewelry  
which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear protective hair cover-  
ing to contain long hair.  
20. NEVER LEAVE TOOL RUNNING  
UNATTENDED. Turn the power off,  
and do not leave tool until it comes to  
a complete stop.  
12. ALWAYS USE SAFETY GLASSES.  
Also use face or dust mask if cutting  
operation is dusty. Everyday eye-  
glasses only have impact resistant  
lenses, they are NOT safety glasses.  
21. NEVER ALLOW UNTRAINED  
USERS TO RUN THIS TOOL  
WHILE UNSUPERVISED.  
13. SECURE WORK. Use clamps or a  
vise to hold work when practical. It is  
safer than using your hand and frees  
both hands to operate tool.  
22. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING THE TOOL. Seek formal  
training or research books or maga-  
zines that specialize in power tools.  
14. DO NOT OVERREACH. Keep proper  
footing and balance at all times.  
-2-  
G6042/G6043 18 Gauge Stapler Kit  
 
Basic Stapler Safety  
In addition to the rules stated in the previ-  
ous section, and those in the warning  
boxes throughout this manual, please  
observe the following safety tips for your  
new stapler:  
1. READ THIS ENTIRE MANUAL  
BEFORE OPERATING THE STA-  
PLER.  
2. ALWAYS DISCONNECT AIR FROM  
THE STAPLER whenever servicing  
or installing staples. During mainte-  
nance, a stapler connected to air may  
fire accidentally, causing serious per-  
sonal injury.  
3. DO NOT PLACE HANDS NEAR  
STAPLE POINT OF ENTRY. Staple  
can deflect and tear through the sur-  
face of the workpiece, puncturing  
your hand or fingers.  
4. NEVER CONNECT THE STAPLER  
TO PRESSURIZED OXYGEN OR  
OTHER COMBUSTIBLE GASES as  
a power source. Only use filtered,  
lubricated, and regulated compressed  
air.  
Operating this stapler can propel  
objects into the air, causing immedi-  
ate eye damage. To protect yourself,  
always wear American National  
Standards Institute (ANSI) approved  
safety glasses or goggles when oper-  
ating this equipment. In addition, this  
stapler discharges at 85-90 decibels.  
To protect your hearing, always wear  
ANSI approved ear protection when  
operating this stapler.  
5. NEVER USE GASOLINE OR  
OTHER FLAMMABLE LIQUIDS TO  
CLEAN THE STAPLER. Vapors in  
the tool will ignite by a spark and  
cause the tool to explode.  
6. DO NOT CARRY THE STAPLER BY  
ANY OTHER PART THAN THE  
HANDLE, and do not carry the sta-  
pler by the air hose.  
7. DO NOT KEEP THE TRIGGER  
PULLED ON THE SAFETY YOKE  
MECHANISM WHEN CARRYING  
OR HOLDING THE TOOL.  
Never point this stapler at yourself or  
another person! Always pay attention  
to the direction this stapler is pointed.  
Use this tool with respect and caution  
to lessen the possibility of operator or  
bystander injury. Ignoring this warn-  
ing may result in serious personal  
injury.  
8. DO NOT USE A CHECK VALVE OR  
ANY OTHER FITTING that allows air  
to remain in the tool.  
-3-  
G6042/G6043 18 Gauge Stapler Kit  
 
INTRODUCTION  
Most importantly, we stand behind our  
Commentary  
tools. If you have any service questions or  
parts requests, please call or write us at  
the location listed below.  
We are proud to offer the Grizzly Model  
G6042/G6043 18 Gauge Stapler. This  
model is part of a growing Grizzly family of  
fine power tools. When used according to  
the guidelines set forth in this manual, you  
can expect years of trouble-free, enjoy-  
able operation and proof of Grizzly’s com-  
mitment to customer satisfaction.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Pennsdale, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
This stapler features 360˚ adjustable  
exhaust, a convenient bottom-loading  
magazine, a safety trigger and a durable  
plastic carrying case.  
We are pleased to provide this manual  
with the Model G6042/G6043. It was writ-  
ten to encourage safety considerations  
and guide you through general operating  
procedures and maintenance. This manu-  
al represents our effort to produce the best  
documentation possible.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model G6042/G6043 as supplied when  
the manual was prepared. However,  
owing to Grizzly’s policy of continuous  
improvement, changes may be made at  
any time with no obligation on the part of  
Grizzly. If you have any comments regard-  
ing this manual, please write to us at the  
address below:  
Read the manual before assembly  
and operation. Become familiar with  
this tool, its safety instructions, and  
its operation before beginning any  
work. Serious personal injury may  
result if safety or operational infor-  
mation is not understood or followed.  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
-4-  
G6042/G6043 18 Gauge Stapler Kit  
 
Compressed Air System  
Safety Yoke Mechanism  
The Model G6042/G6043 is designed to be  
operated at 60-100 psi. Do not exceed  
the maximum operating pressure for  
your model.  
A safety yoke mechanism (bump fire) on  
the nose of the stapler acts as a secondary  
safety device. When the trigger is pressed,  
the stapler will not fire until the safety yoke  
mechanism is depressed.  
Before you use your new stapler, install the  
3
8" quick connect fitting that comes with the  
Before you use your stapler for the first  
time, check the safety yoke mechanism to  
ensure proper function. To do this:  
stapler. Install a female 38" fitting on the air  
hose. Regulate the air pressure on your air  
compressor to barely over the minimum psi  
for your model.  
1. Make sure the stapler is discon-  
nected from the air supply!  
Many pneumatic tools benefit from an in-  
line filter/lubricator/regulator unit. This  
attachment is connected by hoses  
between the air compressor and the sta-  
pler. Using this unit protects your tool from  
damaging water build-up, allows you to  
adjust and maintain constant air pressure  
to your tool, and saves you the inconve-  
nience of having to manually lubricate your  
tool every time you use it. Check the cur-  
rent Grizzly catalog for availability of this  
unit. If you plan on installing a filter/lubrica-  
tor/regulator unit in your compressed air  
system, always follow the connection  
instructions that come with the unit.  
2. Make sure the magazine is empty and  
contains no staples.  
3. Make sure the trigger and the safety  
yoke mechanism move up and down  
without sticking.  
4. Connect the stapler to the air supply.  
5. Without pressing the trigger,  
depress the safety yoke mechanism  
against a scrap piece of wood that is  
clean and free of any knots, staples,  
or other foreign objects. If the stapler  
does not fire, then the safety yoke  
mechanism is working correctly. If the  
stapler does fire when you do this,  
immediately disconnect the stapler  
from the air supply and call our cus-  
tomer service for help.  
Similarly if the stapler fires when the trigger  
is pulled, without the safety yoke mech-  
anism being depressed, then the stapler  
is not working properly.  
If either of these two conditions develop  
after you have used your stapler for a peri-  
od of time, check the lubrication of these  
mechanisms.  
Exceeding the maximum permissible  
operating pressure may cause the sta-  
pler to explode, blowing metal frag-  
ments in all directions. To protect  
yourself from serious personal injury,  
DO NOT allow your air compressor to  
exceed the recommended pressure  
when connected to this stapler!  
The safety yoke is  
a
mechanical  
device that can fail. Never rely on the  
safety yoke mechanism as an excuse  
to point the stapler at yourself or any  
bystanders. Serious injury may occur.  
-5-  
G6042/G6043 18 Gauge Stapler Kit  
 
OPERATION  
4. Point the stapler up and insert a stick  
Loading Stapler  
of staples into the magazine as shown  
in Figure 2. Make sure that the point-  
ed ends of the staples point in the  
same direction as the stapler nose  
piece.  
To load your stapler:  
1. Disconnect the air supply from the  
stapler!  
2. Push the magazine latch in the direc-  
tion shown in Figure 1.  
Figure 2. Loading staples into stapler.  
5. Push the magazine cover forward  
until the magazine latch locks in  
place.  
Figure 1. Releasing magazine latch.  
3. Pull back the magazine cover until it  
stops.  
-6-  
G6042/G6043 18 Gauge Stapler Kit  
 
Operating Stapler  
If you have not read the safety instruc-  
tions in this manual, do not operate the  
stapler.  
Before you operate your stapler, place one  
drop of the included oil into the quick con-  
nect fitting where the stapler connects to  
the air supply. Fire the EMPTY stapler 3-4  
times before beginning, so oil does not  
come out onto the project during regular  
operation.  
Figure 3. Example of staple deflection.  
Besides damaging your workpiece,  
deflection can cause injury if your free  
hand is securing the workpiece in the  
location that the staple deflects.  
To operate your stapler:  
4. Press the trigger. If the staple drove  
into the wood far enough, continue  
with your intended operations. If the  
staple either went too far or not far  
enough, then adjust the air pressure.  
More air pressure will make the staple  
go deeper and less air pressure will  
decrease the staple penetration.  
1. Connect the air supply to the quick  
connect fitting.  
2. Test the loaded stapler for proper  
penetration. Hold the stapler perpen-  
dicular to the surface of a piece of  
clean scrap wood that is thick enough  
for the length of staples you have  
loaded. Depress the safety yoke  
mechanism on your workpiece.  
3. Before pressing the trigger, make  
sure your free hand is positioned out  
of the way of a potential path of a sta-  
ple in case of deflection. (Deflection is  
caused when the staple changes its  
path, resulting in the staple puncturing  
the surface of the workpiece as  
shown in Figure 3.)  
-7-  
G6042/G6043 18 Gauge Stapler Kit  
 
To clear a jammed staple from the maga-  
zine:  
Clearing Jammed Staples  
The most frequent situation with any type  
of stapler is a staple jam. A jammed staple  
must be cleared before using the stapler  
again. The two places where a staple can  
get jammed are the magazine and the dis-  
charge area.  
1. Disconnect the stapler from the air  
supply!  
2. Open the magazine cover and pull the  
magazine all the way back.  
3. Locate and remove the jammed sta-  
ple with a pair of needle nose pliers.  
Close the magazine cover so it latch-  
es.  
To clear a jammed staple from the dis-  
charge area:  
1. Disconnect the stapler from the air  
supply!  
2. Remove all of the staples from the  
magazine.  
3. The jammed staple should now be  
visible; remove it from the discharge  
area with needle nose pliers.  
4. Replace the staples. Push the maga-  
zine closed and snap the quick  
release latch back into operating posi-  
tion.  
Always disconnect air from stapler  
whenever clearing a jammed staple!  
-8-  
G6042/G6043 18 Gauge Stapler Kit  
 
Oiling Stapler  
Cleaning Stapler  
Special oil has been included with you new  
Grizzly stapler to help maintain its useful  
life. Place one drop of oil in the stapler air  
inlet (as shown in Figure 4) before every  
use. Wipe off any excess oil near the sta-  
pler exhaust to avoid dust build-up. When  
the oil that was included with the stapler  
has been completely used, replace with  
Grizzly Model G2820 Pneumatic Tool Oil.  
Use a good solvent to clean the nose  
assembly of the stapler. Always be sure  
that the stapler is dry before using it again.  
Do not allow dust, chips, sand, etc. into the  
air connectors or into the body of the sta-  
pler; this may result in leaks and damage  
to the stapler and the air couplings.  
Another option to manual oiling would be  
to install a lubricator in your air compressor  
line. If your air compressor line already has  
a lubricator, then regular lubrication of your  
stapler will not be necessary. Just make  
sure there is always oil in the lubricator.  
As mentioned before, the best option is to  
install a filter/lubricator/regulator unit such  
as the Grizzly Model H2333 in your air line.  
Never use use gasoline or other flam-  
mable liquids to clean this tool.  
Vapors in the tool may ignite, causing  
the tool to explode. Ignoring this  
warning may lead to serious personal  
injury or even death!  
Figure 4. Lubricating stapler via air inlet.  
Always disconnect air from stapler  
whenever servicing! During mainte-  
nance, a stapler connected to air  
may fire accidentally, causing seri-  
ous personal injury!  
-9-  
G6042/G6043 18 Gauge Stapler Kit  
 
Replacing Pistons/O-Rings  
If you use your stapler day in and day out,  
Grizzly offers repair pistons as cheap  
insurance against wasted down time and  
lost profits in the event that a piston or pis-  
ton shaft becomes worn out. To replace a  
piston:  
Figure 5. Removing stapler exhaust cap.  
8. With a long flathead screwdriver or  
similarly shaped tool, push the piston  
shaft back inside the stapler until you  
can grip the piston head and remove  
it from the cylinder. (Be careful not to  
scratch the discharge area when  
pushing the piston shaft with the  
screwdriver.)  
9. Place a new O-ring on the new piston  
and apply a thin film of the stapler  
lubricating oil on the O-ring.  
Always disconnect air from stapler  
whenever servicing! During mainte-  
nance, a stapler connected to air  
may fire accidentally, causing seri-  
ous personal injury!  
10. Insert the new piston in the cylinder.  
Make sure that the grooves on the  
piston shaft line up with those on the  
guide. The new piston should easily  
slide into the cylinder. Do not force  
the piston into the cylinder! If the  
piston is not easily inserted, double-  
check the alignment of the piston  
shaft with the grooves on the guide.  
11. After the piston is inserted correctly,  
close the magazine. Replace the rear  
cap assembly and tighten the 4 cap  
screws.  
1. Disconnect the stapler from the air  
supply!  
2. Remove all staples from the maga-  
zine cartridge.  
3. Remove the 4 cap screws from the  
stapler exhaust cap.  
4. Remove the exhaust cap as shown in  
Figure 5.  
5. The top of the piston should now be  
visible inside the cylinder, which is  
housed in the head of the stapler.  
6. Open the magazine.  
12. For more assistance, or to install a  
complete O-ring set, refer to the  
appropriate breakdown diagram in the  
back of this manual.  
7. Watch the discharge area and push  
the top of the piston with your finger.  
You will see the piston shaft slide  
down the discharge area.  
-10-  
G6042/G6043 18 Gauge Stapler Kit  
 
MAINTENANCE NOTES  
-11-  
G6042/G6043 18 Gauge Stapler Kit  
 
G6042 PART BREAKDOWN  
-12-  
G6042/G6043 18 Gauge Stapler Kit  
 
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
01 P6042001 CAP SCREW  
02 P6042002 LOCK WASHER  
03 P6042003 CAP  
42 P6042042 NOSE COVER  
43 P6042043 CAP SCREW  
44 P6042044 CAP SCREW  
45 P6042045 LOCK WASHER  
46 P6042046 NOSE  
04 P6042004 SEAL  
05 P6042005 SPRING  
06 P6042006 O-RING  
47 P6042047 SET PLATE  
48 P6042048 SET PLATE  
49A P6042049A STAPLE GUIDE UNIT  
50 P6042050 MAGAZINE  
51 P6042051 PUSHER  
07 P6042007 CAP SEAL  
08 P6042008 PISTON HEAD VALVE  
08A P604200A PISTON HEAD ASSY  
09 P6042009 O-RING  
10 P6042010 STOPPER  
11 P6042011 O-RING  
52 P6042052 SLIDE BLOCK  
53 P6042053 SPRING  
12 P6042012 COLLAR  
54 P6042054 ROD  
13 P6042013 O-RING  
55 P6042055 SHAFT  
14A P6042014A DRIVER ASSEMBLY  
18 P6042018 O-RING  
56 P6042056 SET BLOCK  
57 P6042057 STEPPED PIN  
58 P6042058 END CORE  
59 P6042059 ROUND HD CAP SCR  
60 P6042060 TORSION SPRING  
61 P6042061 STOPPER  
62 P6042062 E-RING  
19 P6042019 CYLINDER  
19A P6042019A COLLAR  
20 P6042020 BUMPER  
21 P6042021 O-RING  
23 P6042023 BODY  
24 P6042024 E-RING  
63 P6042063 CAP SCREW  
64 P6042064 CAP SCREW  
65 P6042065 LOCK NUT  
66 P6042066 COVER  
25 P6042025 JOINT GUIDE  
26 P6042026 SPRING  
27 P6042027 GUIDE SAFETY LVR  
31 P6042031 SAFETY YOKE  
32 P6042032 STEPPED PIN  
33 P6042033 O-RING  
67 P6042067 AIR FITTING  
68 P6042068 O-RING  
69 P6042069 BRACKET  
71 P6042071 LOCK NUT  
72 P6042072 SPRING  
34 P6042034 TRGR VALVE HEAD  
35 P6042035 TRGR VALVE STEM  
36 P6042036 O-RING  
74 P6042074 EXHAUST COVER  
75 P6042075 CAP SCREW  
37 P6042037 O-RING  
38 P6042038 TRGR VALVE GUIDE  
39 P6042039 SPRING  
76 PRP50M  
RUBBER INLET PLUG  
500 P6042500 PISTON/O-RING SET*  
501 P6042501 CARRYING CASE*  
502 P6042502 O-RING SET*  
40A P6042040A TRIGGER  
41 P6041041 CAP SCREW  
* These items are not shown in the illustration.  
-13-  
G6042/G6043 18 Gauge Stapler Kit  
 
G6043 PART BREAKDOWN  
-14-  
G6042/G6043 18 Gauge Stapler Kit  
 
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
01 P6043001 CAP SCREW  
02 P6043002 LOCK WASHER  
03 P6043003 CAP  
40A P6043040A TRIGGER  
41 P6045041 CAP SCREW  
42 P6043042 NOSE COVER  
43 P6043043 CAP SCREW  
44 P6043044 CAP SCREW  
45 P6043045 LOCK WASHER  
46 P6043046 NOSE  
04 P6043004 SEAL  
05 P6043005 SPRING  
06 P6043006 O-RING  
07 P6043007 CAP SEAL  
08 P6043008 PISTON HEAD VALVE  
08A P604300A PISTON HEAD ASSY  
09 P6043009 O-RING  
47 P6043047 SET PLATE  
48 P6043048 SET PLATE  
49A P6043049A STAPLE GUIDE UNIT  
50 P6043050 MAGAZINE  
51 P6043051 PUSHER  
10 P6043010 STOPPER  
11 P6043011 O-RING  
12 P6043012 COLLAR  
52 P6043052 SLIDE BLOCK  
53 P6043053 SPRING  
13 P6043013 O-RING  
14A P6043014A DRIVER ASSEMBLY  
18 P6043018 O-RING  
54 P6043054 ROD  
55 P6043055 SHAFT  
19 P6043019 CYLINDER  
19A P6043019A COLLAR  
56 P6043056 SET BLOCK  
57 P6043057 STEPPED PIN  
58 P6043058 END CORE  
59 P6043059 CAP SCREW  
60 P6043060 TORSION SPRING  
61 P6043061 STOPPER  
62 P6043062 E-RING  
20 P6043020 BUMPER  
21 P6043021 O-RING  
22 P6043022 O-RING  
23 P6043023 BODY  
24 P6043024 E-RING  
25 P6043025 JOINT GUIDE  
26 P6043026 SPRING  
63 P6043063 CAP SCREW  
64 P6043064 CAP SCREW  
65 P6043065 LOCK NUT  
66 P6043066 COVER  
27 P6043027 GUIDE SAFETY LVR  
29 P6043029 LOCK NUT  
30 P6043030 PHLP HD SCREW  
31 P6043031 SAFETY YOKE  
32 P6043032 STEPPED PIN  
33 P6043033 O-RING  
67 P6043067 AIR FITTING  
68 P6043068 O-RING  
71 P6043071 LOCK NUT  
72 P6043072 SPRING  
34 P6043034 TRGR VALVE HEAD  
35 P6043035 TRGR VALVE STEM  
36 P6043036 O-RING  
74 P6043074 EXHAUST COVER  
75 P6043075 CAP SCREW  
76 P6043077 RUBBER INLET PLUG  
500 P6043500 PISTON/O-RING SET*  
501 P6043501 CARRYING CASE*  
502 P6043502 O-RING SET*  
37 P6043037 O-RING  
38 P6043038 TRGR VALVE GUIDE  
39 P6043039 SPRING  
* These items are not shown in the illustration.  
-15-  
G6042/G6043 18 Gauge Stapler Kit  
 
TROUBLESHOOTING  
CAUSE  
PROBLEM  
ACTION  
1. O-rings in trigger valve  
housing are damaged.  
1. O-rings must be replaced  
Air leaking at trigger valve  
area.  
&
operation of safety  
yoke must be checked.  
1. Loose screws in housing.  
2. Damaged O-ring.  
3. Loose air fitting.  
1. Tighten screws.  
2. Replace O-ring.  
3. Tighten air fitting.  
Air leaking between hous-  
ing and hose.  
1. Damaged seal.  
1. Air leaks.  
1. Replace damaged seals.  
Air leaking between hous-  
ing and cap assembly.  
1. Tighten screws and fit-  
tings.  
Tool skips staples while dis-  
charging.  
2. Dirt in nose.  
2. Clean nose.  
3. Dirt or damage prevents sta-  
ples from moving freely in  
magazine.  
3. Clean magazine and  
inspect/repair damage.  
4. Inadequate air flow to tool.  
4. Check fitting, hose, com-  
pressor & air pressure.  
5. Replace piston O-ring.  
Lubricate.  
5. Worn O-ring on piston or  
lack of lubrication.  
6. Damaged O-rings on trigger  
valve.  
6. Replace trigger valve O-  
rings.  
7. Worn bumper.  
8. Cap seal leaking.  
7. Replace bumper.  
8. Replace cap seal.  
1. Stapler is not sufficiently  
lubricated.  
2. Broken spring in cap assem-  
bly.  
1. Lubricate stapler.  
2. Replace spring.  
Tool runs slowly or has a  
loss of power.  
3. Exhaust port in cap is  
blocked.  
3. Clean or replace dam-  
aged internal parts.  
1. Staples are the wrong size.  
2. Staples are bent.  
3. Magazine or nose screws  
are loose.  
1. Use correct staples.  
2. Use undamaged staples  
3. Tighten magazine and  
nose screws.  
Fasteners frequently jam  
the stapler.  
4. Driver or driver guide are  
worn or damaged.  
4. Replace worn or dam-  
aged parts.  
1. Staple is jammed in mag-  
azine or discharge area.  
2. Piston shaft is damaged.  
3. Air pressure too low.  
1. Clear stapler magazine  
or discharge area.  
2. Replace piston shaft.  
3. Check/increase air pres-  
sure.  
Stapler does not fire.  
G6042/3 18 Gauge Stapler Kit  
-16-  
 
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Authorization Number,” which must be clearly posted on  
the outside as well as the inside of the carton. We will not accept any item back without this  
number. Proof of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Pennsdale, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon!  
-17-  
G6042/G6043 18 Gauge Stapler Kit  
 
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model #___________________________ Order #_______________________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
4. How long have you been a woodworker?  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
12. What new accessories would you like Grizzly  
Industrial to carry?  
5. How would you rank your woodworking skills?  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
6. What stationary woodworking tools do you own?  
Check all that apply.  
13. What other companies do you purchase your tools  
and supplies from?  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
_________________________________________  
_________________________________________  
_________________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
14. Do you think your purchase represents good value?  
___Yes  
___No  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
___Other______________________________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
7. How many of your woodworking machines are  
Grizzly? _____________  
___Yes  
___No  
8. Which benchtop tools do you own? Check all  
that apply.  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___8" Table Saw  
___Scroll Saw  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___Other______________________________  
 
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT STAPLE  
 

Graco Inc Pressure Washer 205 985 User Manual
Graco Marine Sanitation System 308 017 User Manual
Graham Field Bathroom Aids 7927A User Manual
Haier Flat Panel Television 1509 A User Manual
Hans Grohe Plumbing Product 31263XX1 User Manual
Havis Shields Automobile Accessories KK 100 05 User Manual
Honeywell Air Cleaner HHT 080 User Manual
HP Hewlett Packard Laptop 110 User Manual
IBM Engraver EGX 600 User Manual
IBM Network Card NetFlex 2 User Manual