Universal Remote Control Universal Remote UR5L 6200L User Manual

TM  
*Note : 10 blinks represents the number zero.  
STEP3 Point the remote control toward the  
Component and enter the 3-digit code  
number assigned to your brand.  
*Note : If the 3-digit code number you just entered is  
correct, the Component will turn Off. If it did not  
turn Off, continue entering code numbers listed  
for that brand until the Component turns Off.  
STEP2 Line up the CLIKR -5 to the other remote,  
STEP2 Press the [VOL  
] button.  
Introduction  
Button Functions  
4
1
head-to-head, 1 or 2 inches apart.  
Operating Instructions For  
Example : One blink, (pause), eight blinks, ( pause) and  
STEP3 Press the [TV] button again. The Component  
TM  
three blinks, indicates code number 183.  
STEP3 Press any button on the CLIKR -5 that you  
TM  
LED will blink twice to confirm the programming.  
The CLIKR -5 UR5L-6200 is designed to  
operate the Motorola DCT6208 advanced HD  
set top and the Motorola DCT2XXX,  
DCT5XXX Series set tops, plus majority of TV,  
VCR, DVD and AUDIO equipment on the  
market as shown below.  
th  
want to teach a command to. For example,  
if you want to teach the [MUTE] button,  
press the [MUTE] button.  
G. AUX Function: Programming a 5 Component  
To return to original state:  
If you wish to restore the CABLE channel control in TV  
th  
You can take advantage of the AUX function to program a 5  
Component such as a second TV, VCR, DVD or Audio Component.  
CLIKR -5  
mode, repeat the above steps but press [CBL] in STEP3  
.
STEP4 Press and hold the [MUTE] button on the  
TM  
th  
STEP4 After you’ve entered the correct code number  
and the Component has turned Off, press the  
[POWER] button to turn the Component back  
On. Now it’s time to test the VOLUME and  
MUTE buttons for the TV (or PLAY and STOP  
buttons for VCR and DVD) to make sure they all  
work. If any of the functions do not work as they  
should, repeat from STEP 3 using the next 3-digit  
code number listed for that brand.  
STEP5 Once you have found the correct 3-digit code,  
save it by pressing the same [COMPONENT]  
button one more time. The Component LED  
light will blink twice to confirm that the code  
was successfully stored.  
other remote until the CLIKR -5 Component  
STEP1 Turn on the 5 Component you want to program  
Cable Remote Control  
J. Programming Volume Control  
LED light blinks twice.  
(TV, VCR, DVD or Audio) using your old remote.  
You can program the volume controls (Volume Up and  
Volume Down) from one Component to operate in  
another Component mode. Default volume control  
settings on the remote control are as follows:  
CABLE : Cable Converters  
TV : Televisions  
*Note : The LED will blink 5 times if there was an  
error in the learning process. In so, repeat  
STEPS 3 and 4. Continue learning other  
buttons by repeating STEPS 3 and 4.  
STEP2 Press the [AUX] button and the [OK/SEL] button  
simultaneously for 3 seconds.The [AUX]  
Component LED will turn on for 30 seconds.  
VCR : VCRs and TV/VCRs  
DVD: DVD Players  
UR5L-6200L  
AUX : Audio Receivers and DVRs, etc.  
STEP3 Press the [COMPONENT] button you want to  
setup. Point the remote control toward the  
Component and enter the 3-digit code number  
assigned to your brand.  
CBL : TV  
T V : TV  
VCR : TV  
STEP5 Once you have completed teaching  
DVD : TV  
AUX : AUX  
Replacing Batteries  
2
TM  
CLIKR -5 all desired commands for that  
If you wish to store the CBL volume control in CBL mode,  
use the following steps.  
Component, save the learned commands by  
pressing the [COMPONENT] and [ASPECT]  
buttons simultaneously until the Component  
LED blinks 3 times. Now test all the buttons  
to make sure they learned correctly.  
Before you program or operate the remote  
control, you must install two new AA alkaline  
batteries.  
*Note :If the 3-digit code number you just entered is the  
correct number, the Component will turn Off. If it  
did not turn Off, continue entering code numbers  
listed for that brand until the Component turns Off.  
STEP1 Press the [CBL] button and the [OK/SEL] button  
simultaneously for 3 seconds. The [CBL]  
Component LED will turn on for 30 seconds.  
STEP1 Remove the battery compartment cover  
STEP2 Press the [VOL  
] button.  
on the back of your remote control.  
Now, program the rest of your Components by  
repeating STEPS 1-5  
*Note : If the Pre-Programmed Method did not  
work, or if the Code Tables do not list your  
Component brand, use the Auto-Search  
Method as explained in Section B.  
D. Erasing a Single Learned Command  
STEP1 Press the [COMPONENT] and [ASPECT]  
buttons simultaneously for 3 seconds  
until the Component LED light turns on.  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If any of  
the functions do not work as they should, you  
need to find a new code.  
STEP3 Press the [CBL] button. The Component LED  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
will blink twice to confirm the programming.  
To return to original state:  
If you wish to restore the TV volume control in CBL mode,  
STEP5 Once you have found the correct 3-digit code,  
save it by pressing the [AUX] button one more  
time. The Component LED light will blink twice  
to confirm the code was stored. Now when  
you press the AUX button, all the buttons will  
STEP2 Press and hold the button you want to erase  
for 3 seconds. The Component LED will blink  
twice to confirm the erasure.  
STEP3 Replace the battery compartment cover.  
repeat the above steps but press [TV] in  
.
STEP3  
B. Auto-Search Method  
STEP1 Turn on the Component you want to  
program (TV, VCR, DVD or AUX) using your  
old remote.  
K. Programming a ‘Macro’ or Favorite Channel  
STEP3 To exit, press and hold both the  
[COMPONENT] and [ASPECT] buttons  
simultaneously until the Component LED  
blinks 3 times.  
th  
In CBL mode, the M1, M2 and HELP buttons can be  
programmed to act as a ‘Macro’ or Favorite Channel  
button. This allows you to send up to 10 commands with  
one button press.  
work with that 5 Component.  
H. Programming the System On/Off Button  
This allows you to program the System On/Off button so it can  
send up to five power On/Off commands with one button press.  
STEP2 Press the [COMPONENT] button (TV, VCR,  
DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED light will turn  
on for 30 seconds indicating the unit is ready  
to be programmed.  
E. Erasing All Learned Commands from One Component  
STEP1 Press the [COMPONENT] and [ASPECT]  
buttons simultaneously for 3 seconds until  
the Component LED light turns on.  
STEP1 Press the [CBL] button to select the CBL mode.  
STEP1 Press the [CBL] button.  
STEP2 Press the [M1,M2 or HELP] button and [OK/SEL]  
button simultaneously for 3 seconds. The [CBL]  
Component LED will turn on for 30 seconds.  
STEP2 Press the [SYSTEM ON/OFF] button and the  
[OK/SEL] button simultaneously for 3 seconds.  
The [CBL] button will turn on for 30 seconds.  
STEP2 Press and hold both the [COMPONENT]  
button you want to erase and the [PAUSE]  
button for 3 seconds. The Component LED  
will blink twice to confirm the erasure.  
STEP3 Press up to 10 buttons you wish to store. The  
[CBL] Component LED will blink once for each  
command entered.  
STEP3 Point the remote toward the Component and  
press the [CH] or [CH] button one step  
at a time or keep it pressed. The remote will  
emit a series of ON/OFF commands.  
Release the [CH] or [CH] button as soon  
as the Component turns Off.  
STEP3 Press the first [COMPONENT] button you want  
to store in the [SYSTEM ON/OFF] button and  
then the [POWER] button. Repeat this for other  
Components until you have stored all the  
desired power commands into the [SYSTEM  
ON/OFF] button.  
STEP4 Press the [CH ] button to store the commands  
STEP3 To exit, press and hold both the  
[COMPONENT] and [ASPECT] buttons  
simultaneously until the Component LED  
blinks 3 times.  
that were selected. The [CBL] Component LED  
will blink twice to confirm the storage of  
commands.  
Programming the Remote Control  
There are three ways you can program your CLIKR -5 remote:  
5
TM  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If any of  
the functions do not work as they should,  
repeat from STEP 3 using [CH] or [CH]  
buttons to find the correct code.  
The Pre-Programmed 3-Digit Code Method  
The Auto-Search Method  
*
*
Operations  
3
STEP4 Press the [CH] button to save the power  
L. Low Battery Warning  
F. Finding a Component Button’s Setup Code Number  
commands you stored. The [CBL] button will  
blink twice to confirm the commands have  
been saved.  
The Learning Method  
*
When the batteries are low and need to be replaced with  
fresh batteries, the Component LED lights will blink 2  
times in sequence whenever a [POWER] button is  
pressed to turn on equipment.  
If you used either the Auto-Search or Learning  
Methods to program a Component, you may not know  
what the correct code number is. Here is a way for  
you to identify the code number, so you can record it  
for future reference.  
DEFAULT STATE:  
Component Default: CABLE  
Channel Default: CABLE channel and  
numbers operate through the CABLE. You  
have the option of controlling channel and  
numbers through the TV, VCR or DVD. Refer  
to section I for programming steps.  
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers  
that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the three  
methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all  
the codes in the remote control, one at a time. The Learning Method allows you to transfer functions from other  
remotes, one button at a time.  
I. Programming Channel Control  
STEP5 Save the code. (Same as for 3-Digit Code  
You can program the channel controls (Channel Up,  
Channel Down and Last) from one Component to  
operate in another Component mode. Default channel  
control settings on the remote control are as follows:  
Programming Method - Section A).  
M. Memory Lock System  
This remote control is designed to retain programmed  
memory for 10 years even after batteries are removed  
from the remote control.  
Now, repeat the Auto-Search Method for those  
Components you could not program earlier with the  
Pre-Programmed Method. If you can’t find the right  
code using the Auto-Search Method, try the Learning  
Method in Section C.  
IMPORTANT SETUP NOTE!  
STEP1 Press the [COMPONENT] button (TV, VCR, DVD  
or AUX) you want to verify and the [OK/SEL]  
button simultaneously for 3 seconds. The  
Component LED light will turn on for 30 seconds.  
This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If  
you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to  
start over.  
CBL : CBL  
T V : CBL  
VCR : CBL  
N. Record Your Component Set-up Codes  
DVD : DVD  
AUX : AUX  
Volume Default: CABLE volume operate  
through the TV. You have the option of  
controlling volume through the Cable box,  
TV  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
STEP2 Press the [INFO] button and count the number of  
times the Component LED light blinks. This  
number indicates the first digit of the code,  
followed by the second and third, each  
separated by a one second pause when the LED  
will turn off.  
A. Pre-Programmed 3-Digit Code Method  
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.  
If you wish to store the TV channel control in TV mode,  
use the following steps.  
C. The Learning Method  
VCR  
DVD  
AUX  
STEP1 Press the [COMPONENT] button (TV, VCR,  
DVD or AUX) to be programmed and the  
[ASPECT] buttons simultaneously for 3  
seconds until the Component LED light turns on.  
Universal Remote Control, Inc.  
STEP1 Press the [TV] button and the [OK/SEL] button  
simultaneously for 3 seconds. The [TV]  
Component LED will turn on for 30 seconds.  
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button  
simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is  
ready to be programmed.  
VCR or DVD. Refer to section  
programming steps.  
J
for  
OCE-0045H REV 04 (04/10/07)  
 

Technics Stereo Amplifier SUV 300 User Manual
Telex Security Camera PW24 2 User Manual
Tiger Handheld Game System 03 140 User Manual
Toshiba All in One Printer 202s User Manual
Toshiba Marine Radio C70 B User Manual
Toshiba Welding System ste 58761 User Manual
Vacuflo Vacuum Cleaner FC1550 User Manual
Vantec Computer Drive UGT PC302 User Manual
Vizio Flat Panel Television D500i B1 User Manual
Weed Eater Lawn Mower 180530 User Manual