Universal Remote Control Universal Remote OCE 0027A User Manual

OCE-0027A_UR2CBLCV02_Rev15 2009.1.15 6:25 PM 페이지1  
STEP3 Point the remote control toward the  
TV and enter the three-digit code  
number assigned to your brand  
from the code tables.  
Introduction  
Button Functions  
3
1
Operating Instructions  
For CABLEVISION  
Remote Control  
The remote control is designed to operate  
Scientific-Atlanta Explorer 1850, 2000, 3000,  
4200 and 4250HD Series set top boxes and the  
majority of TV’s on the market.  
*Tip : The TV will turn off when the correct  
three-digit code number has been  
entered. You can verify you have  
selected the correct code by pressing  
the [MUTE] button, the TV should turn  
on or turn off.  
*Note : If there is more than one three-  
digit number listed for your brand,  
try one code number at a time until  
your TV turns off.  
Replacing Batteries  
Before you program or operate the remote control,  
you must install two AA alkaline batteries.  
2
STEP1 Remove the battery compartment cover  
STEP4 Store the three-digit code number  
by pressing the [TV] button once  
again. The iO button will blink  
twice to confirm that the code  
has been stored.  
on the back of your remote control.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
STEP3 Replace the battery compartment cover.  
*Note : Try all the functions on the remote  
control. If any of the functions do not  
work as they should, repeat from  
Step 2 using the next three-digit code  
number from the same brand list.  
B. Auto Search Method.  
If the three-digit code numbers assigned to  
your brand do not turn off your TV or the  
code tables do not list your brand, you can  
use the Auto Search Method to find the  
correct three-digit code number for your  
TV by the following steps:  
STEP1 Turn on the TV you wish to operate.  
STEP2 Press the [TV] button and the [SEL]  
button simultaneously for 3 seconds.  
The iO button will turn on.  
*Tip : The iO button will light on for 20 seconds.  
The next step must be entered while  
the iO button is on.  
STEP3 Press the [CH+] or [CH-] button one  
step at a time or keep it pressed.  
The remote will emit a series of  
Power ON/OFF commands. Release  
the [CH+] or [CH-] button as soon as  
the TV turns off.  
*Tip : You can verify that you selected the  
correct code by pressing the [MUTE]  
button. The TV should either turn on or  
turn off.  
Operations  
Programming the Remote Control.  
5
4
Default State :  
Device Default: Scientific Atlanta Explorer  
2000/3000  
A. Three-Digit Code Programming Method.  
The remote control can be programmed by pressing in a three digit code number that  
corresponds to particular manufacturers and brands of TV.  
The three-digit code numbers are listed in the code table of the instruction manual.  
Volume Default : TV volume and mute through  
the TV, with the option of controlling volume  
and mute through the Cable. Refer to Section D  
for programming the volume and mute through  
your Cable.  
STEP1 Turn on the TV you wish to program.  
STEP2 Press the [TV] button and the [SEL] button simultaneously for 3 seconds. The iO button  
STEP4 Press the [TV] button to store the  
code. The iO button will blink twice  
to confirm that the code has been  
stored.  
will turn on indicating the unit is ready to be programmed.  
Universal Remote Control, Inc.  
*Tip : The iO button will light on for 20 seconds. The next step must be entered while the iO button is on.  
OCE-0027A Rev 16(01/15/09)  
 

Taylor Weather Radio 4753 User Manual
Tektronix Sprinkler SC 504 User Manual
Topcom Telephone PHONEMASTER 150 User Manual
Toshiba Computer Drive MK3265GSX User Manual
TRENDnet Computer Accessories TKEX4 User Manual
Troy Bilt Chainsaw TB5018CC TB5020CC User Manual
Tunturi Home Gym CF30 User Manual
Uniden Telephone DECT1820 User Manual
Univex Blower 358799370 User Manual
Vision Fitness Treadmill t9700hrt User Manual