LCD Remote Control
P
Changing the RF Transmission Frequency
The RF remote function may be affected by radio interference, etc. If this happens, you can
change the RF transmission frequency.
To change the RF remote transmission frequency:
1. Open the battery cover on the rear.
2. Change the RF switch setting.
RF
1
2
RF
2
1
After changing remote control’s RF frequency, you also must change the receiver’s RF recep-
tion frequency.
3. To change the receiver’s RF reception frequency.
• Press and hold the RF BAND button (TAPE2/CD2 /MONITOR button) behind the receiver's
front panel door for more than 2 seconds. Each time you do this, the RF reception frequen-
cy switches between RF Band 1 and RF Band 2. Select the same band as the position num-
ber of the remote’s RF switch.
Remote Controllable Range
Your LCD remote transmits RF signals to the receiver, and the receiver sends IR signals back
to the remote.
The remote’s range is about 20 ft
provided there are no obstacles
(see illustration to right).
The remote transmits an infrared
signal in addition to an RF signal.
When RF operation is not possi-
ble because of radio wave condi-
tions, you can aim the remote
towards the receiver and use it as
2WAY LCD REMOTE CONTROL UNIT
a conventional infrared remote
control.
+
-
+
-
Since the LCD remote uses
infrared signals to control other
A/V components and devices,
aim it towards the respective
unit.
/8
1
1
/7
1
2
3
4
7
5
8
6
9
+10
10
0
+100
12
11
RF REMOTE CONTROL UNIT
RC-R0910
The following factors can maximize the performance of your LCD remote:
1. Position the receiver’s RF antenna to achieve maximum RF range.
2. Do not position the receiver near metal (such as heat ducts). Metal can absorb RF signals.
3
3. Do not install the receiver where direct sunlight or high-frequency fluorescent lighting can
shine directly into the infrared remote sensor. This can limit the remote’s operating range.
4. Make sure that the remote’s range is not being affected by other radio frequency transmis-
sions.
5. Do not block the IR transmitter on the remote or on the receiver’s front panel . Even a brief
blockage of the transmission (such as someone walking by) can cause the communication
and feedback to become temporarily erratic. If this happens, press the CONFIRM/SHIFT
button on the remote and it will resume normal operation (you might need to reenter the
interrupted command).
6. When the remote’s operating range gets shorter or the low battery indicator (
on its LCD display, replace all 4 batteries:
) flashes
Programming the LCD Remote to Control Other Components
Your LCD remote can be programmed to control almost any IR-controllable audio-video source
component and television. If the component’s code is not already part of the remote’s exten-
sive library, you can use the remote’s Learn feature to teach the component’s commands to
it. You can also use the Learn function to expand the control capabilities of components with
existing codes.
1. Press the MUSIC or MOVIE button.
The display will show:
4. Use the
and
buttons to select “01:
IR”, and press ‘Enter’. The display will show
a list of the receiver’s input jack sets:
5. Use the
and
buttons to select one
2. Press ‘Menu’. The display will show:
of the receiver’s jack sets that has a com-
ponent connected to it, and press ‘Enter’.
The display will show a list of component
types:
3. Press ‘Setup’. The display will show:
6. Use the
and
buttons to select the
type of component connected to that jack
set, then press ‘Enter’. The display will
show a list of brands:
4
Changing a Setup Code
If you replace an existing component with a
new one you will need to perform steps 1 -
10 to program the remote to control the new
component.
7. Use the
component’s brand, then press ‘Enter’.
and
buttons to select the
Deleting a Setup Code
If you disconnect a component from the sys-
tem and do not replace it, you can remove its
control code from the remote.
• If the manufacturer of your component is
not listed, select ‘Nothing’ and press
‘Enter. You can program the component’s
functions using the remote’s Learning
capability (see below).
1. Repeat steps 1 - 6 above.
2. In step 6, select “No Type” or “Delete”.
• If you select “No Type”, the input will still
appear when you select inputs using the
remote’s MUSIC, MOVIE or TV buttons, but
no component is associated with it.
The display will show a list of control codes
for your component:
• If you select “Delete”, the remote deletes the
input, and it does not appear when you
select inputs using the remote’s MUSIC,
MOVIE or TV buttons.
8. Select the first control code on the list.
Programming a Function in
a Button (Learning)
• If the component is a Kenwood component
connected to the receiver via a System
Control cable, select ‘System’. The remote
will send all commands for the component
to the receiver, which will control the com-
ponent via the System Control cable.
Your LCD remote can learn functions from
almost any standard IR remote. The remote
can learn commands to control a component
that couldn’t be successfully programmed in
the previous section, and the remote can
learn codes to extend the functions of com-
ponents that were suc-
9. Press the remote’s AV POWER button.
TV
MUSIC
MOVIE
AV POWER
SYS.POWER
cessfully programmed.
2WAY LCD REMOTE CONTROL UNIT
• The remote can learn
new functions onto
the buttons marked
gray in the illustration:
The remote will send a “power” test signal to
the component. If the component turns on,
the code you selected was correct. If it does
not turn on, try the next code on the list.
Continue until one of the codes works. If
none of the codes work, you can program the
component’s functions using the remote’s
Learning capability.
• The remote can learn
a different set of
functions for each
+
+
CH.
VOL.
CH.
VOL.
-
-
component that has
been identified to the
remote in steps 1 -
10 of the previous
section). See pages
9 - 14 for the button
layouts of the various
types of components.
• If you entered ‘System’ in step 8, skip this
step.
10. When you have finished step 9 the
remote’s LCD display reverts to step 4.
Repeat steps 4 through 9 for each compo-
nent you want the LCD Remote to control.
5
To Control a Component that Couldn’t To Extend the Functions of a
be Successfully Programmed
Component that was Successfully
Programmed
1. Place the LCD Remote and the remote you
want to learn the commands from head-to-
head, about 4 inches apart:
By using the LCD remote’s “Extend 1 - 5”
functions you can program up to 5 extended
functions for each component you have set
the remote up to control.
1. Place the LCD Remote and the remote you
want to learn the commands from head-to-
head, about 4 inches apart:
2. Press the MUSIC, MOVIE or TV button to
select the component whose commands
you want to learn.
3. Press the remote’s LEARN button.
2. Press the MUSIC, MOVIE or TV button to
select the component you want to add
functions to.
3. Press the remote’s LEARN button.
4. Press the button on the LCD remote into
which you want to program the new func-
tion. The display will show:
The display will show:
5. Press and hold the button with the func-
tion that you want the LCD remote to
learn. Do not move either remote until the
LCD remote’s display changes from
“Waiting” to “Complete”.
• To reset a button to its original factory-pro-
grammed function, press the ‘Clr’ button in
step 3 of the above procedure.
4. Use the and buttons to select ‘Extend1’,
‘Extend2’, ‘Extend3’, ‘Extend4’, or ‘Extend5’;
press ‘Enter’. The display will show:
6. Repeat steps 3 -4 to finish programming
the remote to control the component.
7. Repeat steps 1 - 4 to program the remote
to control a different component.
• When you are finished, press the ‘Exit’ button.
6
5. Press the button on the LCD remote into which you want to program the new function.
6. Press and hold the button with the function that you want the LCD remote to learn. Do not
move either remote until the LCD remote’s display changes from “Waiting” to “Complete”.
• To reset a button to its original factory-programmed function, press the ‘Clr’ button in step
3 of the above procedure.
7. Repeat steps 1 - 6 to program more extended functions for that component, or to program
extended functions for another component.
• When you are finished, press the ‘Exit’ button.
7
Using Your LCD Remote
Note: Pressing the F.SHIFT button (#25) acti-
vates a button’s secondary function
1. LCD display: see page 9
2/3. LCD function buttons 1 and 2:
Selects the function shown directly
above the button on the LCD display
4. CONFIRM/SHIFT button: CONFIRM:re-
establishes interrupted communication
with the receiver; SHIFT: lets you use the
Input Selector buttons (see #17) to select a
component and control it without making it
the active input
5. MACRO button: press to create and execute
macros (see page 15)
6. AV POWER button: turns other A/V system
components on and off
7. AV component control buttons
8. CH.(+/-) buttons: changes channels for the
radio and A/V system components
9. LISTEN M./INPUT MODE button: LISTEN M
cycles through the receiver’s various sur-
round sound modes; INPUT MODE cycles
through the receiver’s different input types
(digital, analog, etc.)
17. Input selector buttons: MUSIC: Selects
the system’s audio components; MOVIE:
Selects the system’s video components;
TV: Controls TVs or video monitors
10. SOUND/DIMMER button: SOUND acti-
vates the receiver’s sound controls;
DIMMER dims the receiver’s fluorescent
display
18. SYS. POWER button: Turns the receiver
on and puts it into standby
19. VOL. (+/-) buttons: Raises and lowers the
receiver’s volume
11. TITLE/GUIDE button: Controls functions
of A/V components
20. MUTE button: Mutes the sound
21. THX/SUB W. button: THX activates the
THX Cinema listening mode
12. Cursor Controls: Controls functions of
A/V components
SUB W. allows control of the receiver’s
subwoofer output volume
13. RETURN/PAGE Down button: Controls
functions of A/V components
22. MENU button: Controls functions of A/V
components
14. REC/REC MODE button: REC activates
recording in an A/V component; REC
MODE cycles the receiver’s record mode
between Auto/Manual/Off
23. OSD/PAGE 5 button: Controls functions
of A/V components
24. LEARN button: Activates the remote’s
learning capability (see page 5)
15. Numeric buttons: Enters numeric com-
mands
25. F.SHIFT button: Activates secondary but-
ton functions
16. LCD display cursor up/down buttons:
Cycles through lists of items that appear
on the remote’s LCD display
8
LCD Display Indicators
1. Playback/recording mode indicators:
Play indicator/ Pause indicator/
Record indicator/ Stop indicator
2. Character display:
Shows various information such as the
source component name and track number.
3. Current function of LCD function button 1
4. Current function of LCD function button 2
5. Communication indicators:
Sending / Receiving.
6. Battery indicator:
appears when the batteries are nearly
exhausted. When it does, replace all of the
four batteries together.
Controlling Other A/V Components
In addition to controlling a Kenwood receiver, your LCD Remote can also control a variety of
A/V components. Since the functions of the remote’s buttons will vary depending on what
component it is controlling, we suggest that you keep the following function charts handy for
reference.
• The remote may not be able to control all A/V components
• Certain components may function differently from the functions shown in this manual
Cassette Deck Operation:
9
CD Player Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
TUNING
TV SELECT
BAND
ENTER
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
: Scan Backward
: Scan Forward
: Play/Pause
: Pause
: Stop
Numeric Entry
TITLE/GUIDE
: Track/Title
With F.SHIFT button:
: Skip Backward
: Skip Forward
REPEAT
: Repeat
RANDOM
: Random Play
: Disc Select (Up)
DISPLAY
: Display
: Disc Select (Down)
LCD Display Functions:
01: Disc Select
02: Set
03: Play Mode
04: Check
07: Track Title
08: All Data Read
09: Subout Monitor
10: Continuous Play
11: All Info
05: Clear
06: Disc Title
CD-R Recorder Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TUNING
BAND
TV SELECT
ENTER
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Play
: Cursor Up
: Pause
: Stop
: Cursor Down
: Cursor Left
: Cursor Right
Numeric Entry
: Skip Backward
: Skip Forward
With F.SHIFT button:
REPEAT
: Record
: Repeat
RANDOM
: Scan Forward
: Shuffle/Random Play
: Display
DISPLAY
: Scan Backward
LCD Display Functions:
01: Open/Close 06: Clear
02: CDR Mode
03: CD Mode
04: Program
05: Record Mute
10
MD Player Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
TUNING
TV SELECT
BAND
ENTER
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
: Scan Backward
: Scan Forward
: Play
: Pause
: Stop
Numeric Entry
TITLE/GUIDE
: Track/Title
: Record
With F.SHIFT button:
: Skip Backward
: Skip Forward
REPEAT
: Repeat
RANDOM
: Random Play
DISPLAY
: Time
DVD Player Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
MENU
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Cursor Up
: Play
: Pause
: Stop
Numeric Entry
: Cursor Down
: Cursor Left
: Cursor Right
With F.SHIFT button:
: Skip Backward
: Skip Forward
REPEAT
MENU
: Repeat
: Menu
: Title
RANDOM
TITLE/GUIDE
: Random Play
: Scan Forward
DISPLAY
OSD
/PAGE
: Display
: Scan Backward
: On-Screen Display
: Return
AUDIO
RETURN
/PAGE
: Audio
With F.SHIFT button:
: Slow Reverse
: Slow Forward
LCD Display Functions:
01: Disc Select
07: Clear
13: All Data Read
02: Chapter/Time 08: Repeat A - B 14: Aspect
03: Angle
09: Subtitles
15: On/Off
04: Program
05: DVD Setup
06: Memory
10: Title Search
11: Disc Title
12: Track Title
11
VCR Operation:
AV POWER
TITLE/GUIDE
MENU
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Cursor Up
: Play
: Pause
: Stop
: Cursor Down
: Cursor Left
: Cursor Right
Numeric Entry
: Rewind
With F.SHIFT button:
MENU
INPUT SEL.
: Menu
: Guide
: Input Select
: Fast-Forward
TITLE/GUIDE
: Channel Up
: Channel Down
: Record
LCD Display Functions:
01: Thumb Up
02: Thumb Down
03: Jump
06: Exit
04: Instant Replay
05: Quick Skip
Laser Disc Player Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
MENU
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Scan Backward
: Play
: Pause
: Stop
Numeric Entry
: Scan Forward
OSD
/PAGE
With F.SHIFT button:
: Skip Backward
: Skip Forward
: On-Screen Display
REPEAT
: Repeat
RANDOM
: Random Play
: Slow Forward
DISPLAY
: Display
: Slow Backward
LCD Display Functions:
01: Frame/Time
02: Side A or A/B
03: Side B
12
TV Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TUNING
TV SELECT
BAND
ENTER
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Mute
: Cursor Up
: Volume Down
: Volume Up
Numeric Entry
: Cursor Down
: Cursor Left
: Cursor Right
With F.SHIFT button:
INPUT SEL.
: Channel Up
: Video Select
: Channel Down
TV SELECT
: TV Select
AUDIO
LCD Display Functions:
: Audio
01: - / - -
02: >12
07: Mix
08: Exit
03: Wide
09 - 13: Extend 1 - 5
04: Picture-In-Picture
05: Text/Mix/TV
06: Text Off
Cable Tuner Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
MENU
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
: Volume Down
: Volume Up
ENTER : Enter
: Cursor Up
Numeric Entry
: Cursor Down
: Cursor Left
: Cursor Right
: Channel Up
With F.SHIFT button:
: Channel Down
EXIT
MENU
: Exit
: Menu
: Guide
INPUT SEL.
TITLE/GUIDE
: Input Select
LCD Display Functions:
DISPLAY
OSD
/PAGE
: On-Screen Display
01: A
02: B
03: C
: Page Up
SELECT
THEME
RETURN
/PAGE
: Select
: Page Down
04 - 08: Extend 1 - 5
: Theme
: Favorite
: Info
FAVORITE
INFO.
LAST CHANNEL
: Last Channel
13
Satellite Receiver Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
MENU
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Cursor Up
: Channel Up
: Channel Down
Numeric Entry
: Cursor Down
: Cursor Left
: Cursor Right
With F.SHIFT button:
INPUT SEL.
OSD
/PAGE
: Input Select
LCD Display Functions:
01 - 05: Extend 1 - 5
SELECT
: On-Screen Display
: Select
AUDIO
: Alternate Audio
DSS Receiver Operation:
AV POWER
REPEAT
RANDOM
DISPLAY
INPUT SEL.
SELECT
TITLE/GUIDE
MENU
TUNING
TV SELECT
BAND
ENTER
RETURN
/PAGE
OSD
/PAGE
AUDIO
INFO.
THEME
FAVORITE
AUTO/MONO
EXIT
LAST CHANNEL
ZONE A/B
STATUS
MULTI ZONE
ENTER : Enter
: Cursor Up
: Channel Up
: Channel Down
Numeric Entry
: Cursor Down
: Cursor Left
: Cursor Right
With F.SHIFT button:
LCD Display Functions:
INPUT SEL.
MENU
: Input Select
: Menu
01: Exit
02 - 06: Extend 1 - 5
SELECT
TITLE/GUIDE
: Select
: Channel Guide
AUDIO
: Alternate Audio
THEME
: Theme
FAVORITE
: Favorite
INFO.
: Info
14
Performing Several Actions at Once (Macros)
Your LCD Remote allows you to perform up to 20 different actions by pressing a single button.
For example, you can create a macro that turns the TV on, turns the VCR on, selects the cor-
rect TV channel or input, and starts the VCR playing. The remote can store 3 different macros.
Creating a Macro
1. Think about the sequence of events you want to set up. You may even want to write down
which actions you want the macro to take and what buttons you need to press (and in what
order) to perform them.
2. Press and hold the MACRO button
for more than 2 seconds.
The display will show:
3. Within 8 seconds, press the MUSIC (Macro1), MOVIE (Macro2) or TV (Macro3) button. The
display will read “MACRO 1”, “MACRO 2” or “MACRO 3”.
4. Press the control buttons for the functions you want the macro to perform in the order you
want them to happen. Press each button slowly and firmly. Each macro can contain a maxi-
mum of 20 different steps.
5. Press the MACRO button to register the macro.
• Since most components take a few seconds after power-up before they will perform anoth-
er function, we recommend programming all of a macro’s power-up commands so they hap-
pen sequentially, then program the other functions of the first component that powered up,
then the second, etc.
• If a macro function is not performed properly, insert some delay time by programming the
function twice.
The display will read “Full” when you have registered 20 steps for a particular macro.
To Use a Macro
1. Press the MACRO button.
2. Within 3 seconds, press the button to which you have programmed the macro (MUSIC,
MOVIE or TV).
• Continually aim the remote at the components until the macro has completed executing.
(The remote’s display will return to the previous screen.)
15
Internet
e-mail:
1-800-KENWOOD
Main Office:
P.O. Box 22745
Long Beach, CA 90801-5745
Canada Office:
6070 Kestrel Rd.
Mississauga, Ontario L5T 1S8
©2002 Kenwood USA Corporation. All Rights Reserved
|