Universal Remote Control Universal Remote URC 4021 User Manual

UNIVERSAL REMOTE CONTROL  
REPLACES  
REMOTES  
4
TV  
DVD  
VCR/PVR  
CBL/SAT  
EASY SETUP  
DIGITAL  
READY*  
FAVORITE  
CHANNEL  
MASTER  
POWER KEY*  
LIMITED  
LIFETIME  
WARRANTY  
*See back for details  
URC 4021  
USES 2 AAA BATTERIES  
 
(NOT INCLUDED)  
TABLE OF CONTENTS  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Programming Device Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Programming A Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Programming The Power Key For The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Operating The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Clearing The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Programming Favorite Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Locking Volume Control To One Mode  
(Global Volume Lock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Unlocking Volume Control For A Single Device  
(Individual Volume Unlock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Unlocking All Volume Control  
(Restoring Default Setting ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Clearing Custom Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Restoring Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Additional Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Setup Codes For Cable Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Setup Codes For Cable Box/PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Setup Codes For DVD Player/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Setup Codes For PVRs (or DVRs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Setup Codes For Satellite Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Setup Codes For Satellite Receiver/PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Setup Codes For TV/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Setup Codes For TV/VCR/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Setup Codes For VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
2
 
INTRODUCTION  
The One ForAll 4 Device Universal Remote Control (URC-4021) is  
designed to remotely operate up to four home entertainment devices.It  
also features intuitive and easy-to-use keys for instant control of DVD and  
PVR (or DVR) components.Moreover,its sophisticated technology will  
allow you to consolidate your original home entertainment remote  
controls into one easy-to-use product. Advanced features include:  
Intuitive buttons to allow easy access to functions and menus on your DVD  
player,PVR (or DVR),and Cable/Satellite devices  
Direct code setup for easy device programming  
Step-and-Set code search and CodeVerification for an alternate way to pro-  
gram devices  
Power Macro for master on/off control of all of your equipment with a single  
keystroke  
Volume Lock/Unlock feature to lock or unlock the volume control to one mode  
or individual modes  
Device Key Re-Assignment to remotely control a second (duplicate) device  
Channel Scan and Favorite Channel Scan for easy channel surfing  
Color-coded keys to quickly locate popular functions  
Extensive code library for popular video devices including DVD players and  
PVRs (or DVRs)  
The URC-4021 remote control requires two (2) new AAA alkaline batter-  
ies (not included) and some easy programming to control your devices.  
For best results, please read and perform all instructions listed here.Also,  
keep this guide for future reference.  
3
 
FEATURES AND FUNCTIONS  
Use the illustration below to locate features on the One ForAll 4 Device  
Universal Remote Control (URC-4021) and then study the Key Charts (on  
the next two pages) to learn how they function.  
To find out what type of devices can be controlled by each device key after  
programming,see the Device Table on page 6.  
4
 
Key Charts  
When the LED (red light) blinks,the remote control is  
working and (after programming) is sending signals.  
Press VCR/PVR,DVD,CBL/SAT,or TV once to select a  
desired home entertainment device to control.  
Also see the Device Table on page 6.  
Press POWER once to turn on or off the selected device.  
For master power control,see Programming  
A Master Power Macro on page 10.  
Use the keypad (1 ~ 9 and 0) to directly select channels  
(e.g.,009 or 031).  
Use TV/VID to switch the TV’s input to view TV or video  
programs.  
Press ENTER once after entering the channel numbers on  
some TVs.  
Use GUIDE to display your selected device’s program  
guide or setup menu.  
Press MENU once to display your selected device’s main  
menu.  
Use INFO to display the current channel and program or  
on-screen directory.  
Use EXIT to exit from your selected device’s guide or  
menu.  
Use the Cursor Keys to move the cursor in the program  
guide and menu screens.  
Use SELECT (OK) to choose options from your selected  
device’s menu or guide.  
Press LAST once to recall the last channel.  
Use FAV to scan all channels,or after programming,  
to scan up to 10 favorite channels.  
Use CHL (or CHM) to select the next higher (or lower)  
channel.  
Press SUBTITLE/CC once to display (or turn off) subtitles or  
closed captions,if availableonyourDVDplayeror  
cable/satelliteservice.  
For a PVR (or DVR),press PVR MENU once to display a  
list of your recorded shows.  
Press MUTE once to turn the sound off or on.  
Use VOLL (or VOLM) to raise (or lower) the sound vol-  
ume.  
5
 
Use REW,PLAY,FWD,PAUSE,or STOP to control yourVCR,  
PVR (or DVR),or DVD player.  
For a DVD player,use SKIP F. or SKIP R. to view the next  
or previous chapter.  
For aVCR,PVR (or DVR),orVOD (if available),use SCAN-  
or SCAN+ to quickly scan forward or back through a video  
program.Use REPLAY for an instant replay.Use QUICK  
SKIP to advance the video program a preset amount (as  
set on your device).  
Press REC twice to record aVCR or PVR (or DVR) program.  
Use SLEEP to set the sleep timer on a selected device if  
equipped with this feature.  
Use SET for all programming sequences.  
Device Table  
NOTE: Please refer to the table below when performing the instructions inProgramming  
Device Controlon page 8.  
After programming,the One ForAll 4 Device Universal Remote Control will  
be able to control the following types of devices:  
DEVICE KEY  
CONTROLS THESE TYPES OF DEVICES  
DVD Player  
TV/DVD Player Combo  
VCR/DVD Player Combo  
VCR  
TV/VCR Combo  
TV/VCR/DVD Player Combo  
VCR/DVD Player Combo  
PVR (or DVR)  
Cable Box (or Converter)  
Cable Box/PVR (or DVR) Combo  
Satellite Receiver  
Satellite Reciver/PVR (or DVR) Combo  
Television  
6
 
INSTALLING BATTERIES  
ƒ
ƒ
1.  
2.  
On the remote control’s back,push the tab and lift off the  
battery cover.  
Obtain two (2) newAAA alkaline batteries.Match the +  
and – marks on the batteries to the + and – marks in the  
battery case,then insert the new batteries.  
3.  
4.  
Press the battery cover back into place.The tab should  
click when the cover is locked.  
Test the remote control by pressing any mode key (e.g.,  
TV).If the batteries are inserted correctly,the LED (red  
light) will blink.  
NOTE:When batteries need replacement, the remote control will stop operating. Remove  
the old batteries and insert new ones within 10 minutes to ensure all of your programming  
information is restored.  
Battery Precautions: Do not mix old and new batteries.• Do not mix alkaline, standard  
(carbon-zinc) or rechargeable (nickelcadmium)batteries.• Always remove old, weak or  
worn-out batteries promptly and recycle ordispose of them in accordance with Local and  
National Regulations.  
7
 
PROGRAMMING DEVICE CONTROL  
The One ForAll 4 Device Universal Remote Control is preprogrammed at  
the factory to operate an RCA TV, a Toshiba DVD player,a Motorola cable  
box,and an RCAVCR.To control devices other than the default brands,per-  
form the following steps;otherwise skip this section:  
1.  
Turn on a desired device (e.g.,VCR or DVD player) and,if  
applicable, insert media (e.g.,cassette or disc).  
NOTE: Please read steps 2 through 4 completely before proceeding.  
Highlight or write down the codes and device you wish to program  
before starting step 2.  
2.  
On the remote control,press a device key once (i.e.,VCR/PVR,  
DVD,CBL/SAT,or TV).  
NOTE: To program control of aVCR, PVR (or DVR),TV/VCR Combo,  
or TV/VCR/DVD Player Combo press VCR/PVR once.After program-  
ming aVCR Combo device, you will be able to control channelselec-  
tion, volume,andVCRfunctions.  
NOTE: To program control of a DVD Player, DVD Player/VCR  
Combo, or TV/DVD Player Combo, press DVD once.After program-  
ming a DVD Combo device,you will be able to control channel selec-  
tion, volume,and DVD functions.  
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)  
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)  
Combo, press CBL/SAT once.  
3.  
4.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
Use the Manufacturer’s Codes (starting on page 18) to  
locate the type of device and brand name and then enter  
the first four-digit code for your device.If performed cor-  
rectly, the LED will blink twice.  
NOTE:If the LED did not blink twice,repeat steps 2 through 4 and enter  
the same code again.  
5.  
6.  
Aim the remote control at the device and press POWER  
once.The device should turn off.If it does not,repeat  
steps 2 through 5,trying each code for your brand until  
you find one that works.If it still doesn’t work,try  
Searching ForYour Code on next page.  
NOTE: If the device does not have a POWER key, press PLAY.  
Repeat steps 1 through 5 for each device you want to con-  
trol. For future reference,write down each working device  
code in the following boxes:  
VCR/PVR Code:  
Device Type:______________  
DVD Code:  
Device Type:______________  
CBL/SAT Code:  
Device Type:______________  
TV Code:  
Device Type:______________  
8
 
SEARCHING FOR YOUR CODE  
If your device does not respond to the remote control after trying all codes  
listed for your brand,or if your brand is not listed at all,try searching for  
your code.  
NOTE:Before performing a code search for a DVD player or aVCR,turn on the device and  
insert the required media.  
For example,to search for a code for your TV:  
1.  
2.  
On the remote control,press TV once.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
3.  
Enter 9 - 9 - 1.The LED will blink twice.  
4.  
Aim the remote control at the TV and slowly alternate  
between pressing POWER and TV.Stop when the TV turns  
off (after pressing POWER).If the device does not have a  
Power key,you can substitute another function,such as  
digits 0 ~ 9 ,CHL,or PLAY).  
NOTE:In the search mode,the remote control will send IR codes from  
its library to the selected device,starting with the most popular code  
first.  
5.  
6.  
To lock in the code,press and release SET.The LED will blink  
twice.  
To search for the codes of your other devices,repeat steps  
1 through 5,but substitute the appropriate device key for  
the device you are searching for.  
CHECKING THE CODES  
If you have set up the remote control using the Searching ForYour Code pro-  
cedure (as above),you may need to find out which four-digit code is operat-  
ing your equipment.For example,to find out which code is operating your  
TV:  
1.  
2.  
On the remote control,press TV once.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
3.  
Enter 9 - 9 - 0.The LED will blink twice.  
4.  
To view the code for the first digit,press 1 once.Wait 3  
seconds,count the LED blinks (e.g.,three blinks = 3) and  
write down the number in the leftmost box in the TV  
code boxes on page 8.  
NOTE: If a code digit is0”, the LED will not blink.  
9
 
5.  
6.  
Repeat step 4 (on the previous page) three more times for  
remaining digits.Use 2 for the second digit,3 for the third  
digit,and 4 for the fourth digit.Write down the code dig-  
its in the remaining TV code boxes on page 8.  
To check for codes of other devices,repeat steps 1  
through 5 (starting on the previous page),but substitute  
the appropriate device key for each device you are check-  
ing. Write down the device’s code digits in the appropri-  
ate code boxes on page 8.  
PROGRAMMING A MASTER POWER MACRO  
In its default state,the POWER key on the One ForAll 4 Device Universal  
Remote Control will individually power your home entertainment devices  
on or off.However,you can also program a Master Power Macro onto the  
POWER key that will sequentially turn on or off all the devices with a single  
key press.  
Programming The Power Key For The Master Power Macro  
1.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
2.  
Enter 9 - 9 - 5.The LED will blink twice.Then press POWER  
once.  
3.  
4.  
For the first device you want in the power-on sequence,  
press its device key (e.g.,CBL/SAT) once.  
Repeat step 3 up to three more times to add desired  
devices to the power-on sequence (e.g., VCR/PVR,DVD,and  
TV).  
5.  
To save the settings and exit the program,press and hold  
SET until the LED blinks twice,then release SET.  
Operating The Master Power Macro  
1.  
After programming,point the remote control at the  
devices and press POWER for at least 2 seconds to sequen-  
tially turn on (or off) your devices.  
NOTE:When POWER is pressed for less than 2 seconds,a power com-  
mand will only be sent to the currently-selected device.This allows  
you to still individually power devices on or off.  
2.  
Devices will turn on (or off) according to your  
programmed sequence.  
NOTE:The currently-selected device will always turn on or off first,  
followed by the remaining programmed sequence.After the master  
power sequence has been completed,the remote control will be set to  
control the first powered-on device.  
NOTE:If one or more devices does not have a POWER key,the power  
off/on sequence may be slightly delayed when the remote control signals  
the device(s).This action is normal.  
continued on next page...  
10  
 
PROGRAMMING A MASTER POWER MACRO (continued)  
Clearing The Master Power Macro  
1.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
2.  
Enter 9 - 9 - 5.The LED will blink twice.Then press POWER  
once.  
3.  
Press and hold SET until the LED blinks twice,then release  
SET.The Master Power Macro is now cleared.  
RE-ASSIGNING DEVICE KEYS  
The One ForAll 4 Device Universal Remote Control can be set to control a  
second PVR,VCR,or DVD player.For example,to control a TV,a cable box,  
and two DVD players,re-assign the unused VCR/PVR key to operate the second  
DVD player as follows:  
1.  
On the remote control,press and hold SET until the LED  
(red light) blinks twice,then release SET.  
2.  
Enter 9 - 9 - 2.The LED will blink twice.  
3.  
4.  
Press DVD once.  
Press VCR/PVR once.The LED will blink twice.The VCR/PVR  
key is now ready to be set up to control your second DVD  
player.See Programming Device Control on page 8.  
To re-assign a secondVCR or PVR (or DVR) to the unused DVD key,repeat  
steps 1 through 4.However,in step 3 substitute VCR/PVR for DVD,and in step 4  
substitute DVD for VCR/PVR.Now the DVD key will be ready to be set up as your  
secondVCR or PVR (or DVR).See Programming Device Control on page 8.  
NOTE: Only one device can be assigned to an unused device key at a time.  
USING CHANNEL SCAN  
In the CBL/SAT or TV mode,use the FAV key to start a 3-second scan of all  
channels.Or,if programmed,use the FAV key to scan only your favorite  
channels to view a desired channel (see Programming Favorite Channel Scan  
on next page.)  
1.  
Press CBL/SAT or TV once.  
11  
 
2.  
Press FAV once.  
If Favorite Channel Scan has been set up,scanning of  
favorite channels will start with up to 100 channel changes  
or until stopped by pressing any key.  
If Favorite Channel Scan has not been set up,scanning  
will start with the current channel,and continue up to  
100 channel changes or until stopped by pressing any key.  
3.  
To stop scanning channels at any time,press any key  
once.  
PROGRAMMING FAVORITE CHANNEL SCAN  
In the CBL/SAT or TV mode,you can store a list of up to 10 favorite channels,  
in any order,that will be immediately scanned when FAV is pressed (see  
Using Channel Scan on the previous page).  
NOTE:Favorite channels can only be programmed for one mode.After programming,if FAV  
is pressed while in another mode,the remote control will start scanning all channels instead  
(if applicable to the selected device).  
1.  
On the remote control,press CBL/SAT or TV once.  
2.  
3.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
Enter 9 - 9 - 6.The LED will blink twice.  
4.  
5.  
Use the keypad to enter a favorite channel number (e.g.,  
031).Then press SET once.  
NOTE: If the original remote control required pressing an Enter key  
to change the channel, also press the ENTER key after the channel  
number (e.g., 0 - 3 - 1 - ENTER). On some satellite receivers and cable  
boxes, you may need to press the SELECT (OK) key instead of ENTER.  
If desired,repeat step 4 for each channel to be stored,up  
to a total of 10 channels.  
NOTE: If you try entering more than 10 channels, the remote control  
will automatically exit programming. To change your favorite chan-  
nel list at this point, you will first need to delete the existing list by  
performing the steps inClearing Custom Programmingon page 14.  
Then, perform the instructions in this section once again.  
6.  
To exit programming with less than 10 favorite channels  
stored,press and hold SET until the LED blinks twice.  
Otherwise,the remote control will automatically exit the  
program after 10 channels have been stored.  
12  
 
CHANGING VOLUME LOCK  
The One ForAll 4 Device Universal Remote Control is set at the factory for  
independent volume control of each selected device.However,you may  
change theVolume Lock setting to GlobalVolume Lock so that a device’s vol-  
ume will be locked to one mode (e.g.,to control TV volume in all other  
modes).After that,if desired,you can perform IndividualVolume Unlock on a  
selected device to set its volume control for independent operation.  
Locking Volume Control To One Mode  
(Global Volume Lock)  
1.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
2.  
Enter 9 - 9 - 3 and then press any mode key once (e.g.,TV).  
The LED will blink twice.  
3.  
Now,when you press VOLL,VOLM,or MUTE,the volume of  
the selected device (e.g.,TV) will be controlled,regardless  
of the mode you have selected.  
Unlocking Volume Control For A Single Device (Individual Volume  
Unlock)  
1.  
After performing GlobalVolume Lock (above),press a desired  
mode key where you want volume to be unlocked (e.g.,  
DVD) and controlled within its own mode.  
2.  
3.  
Press and and hold SET until the LED (red light) blinks twice,  
then release SET.  
Enter 9 - 9 - 3 and then press VOLMonce.The LED will  
blink four times.  
4.  
5.  
If desired,repeat steps 1 through 3 (of this section) for  
each device that you want volume to be unlocked.  
Now,after you select a device that has volume unlocked  
(e.g.,DVD),pressing VOLL,VOLM,or MUTE will control the  
device’s volume only in its own mode.  
Unlocking All Volume Control (Restoring Default Setting)  
NOTE: Performing these instructions will restore independent volume control for all pro-  
grammed devices (e.g., TV volume control in TV mode,VCR volume inVCR/PVR mode,  
etc.).  
1.  
On the remote control,press and hold SET until the LED (red  
light) blinks twice,then release SET.  
13  
 
2.  
Enter 9 - 9 - 3 and then press VOLLonce.The LED will  
blink four times.  
3.  
Volume will again be independently controlled according  
to its default states for all programmed devices.  
CLEARING CUSTOM PROGRAMMING  
The One ForAll 4 Device Universal Remote Control contains an Operational  
Feature Reset program.  
If desired,you can use it to clear custom programming,except your setup  
codes and reassigned device keys,and reset them to original factory set-  
tings. Also see Restoring Factory Default Settings as below.  
IMPORTANT: Executing this program will erase all your custom settings for  
Power Macro, Favorite Channels, and Volume Lock.  
1.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
2.  
Enter 9 - 8 - 0.The LED will blink twice.The remote control  
will return to normal operation.  
RESTORING FACTORY DEFAULT SETTINGS  
The One ForAll 4 Device Universal Remote Control also contains a Factory  
Reset program that you can use to reset all custom settings and setup codes  
to original factory settings.Also see Clearing Custom Programming as above.  
IMPORTANT: Executing this program will erase all your custom settings for  
Power Macro, Favorite Channels,Volume Lock, Reassigned Devices, and all  
device settings.  
1.  
Press and hold SET until the LED (red light) blinks twice,  
then release SET.  
2.  
Enter 9 - 8 - 1.The LED will blink twice.The remote control  
will return to normal operation.  
14  
 
TROUBLESHOOTING  
PROBLEM:  
LED (red light) does not blink when you press a key.  
SOLUTION:  
PROBLEM:  
Replace batteries with two newAAA alkaline batteries.  
LED blinks when you press a key,but home entertain-  
ment device does not respond.  
SOLUTION:  
Make sure the remote control is aimed at your home  
entertainment device and is not farther than 15 feet  
away.  
PROBLEM:  
SOLUTION:  
The unit does not control home entertainment devices  
or commands are not working properly.  
Try all listed codes for the device brands being set up.  
Make sure they can be operated with an infrared remote  
control.  
PROBLEM:  
SOLUTION:  
Changing channels does not work.  
If originalremoterequiredpressingENTERorSELECTto  
changechannels,pressENTERorSELECTonthisremote  
afterenteringthechannelnumber.  
PROBLEM:  
SOLUTION:  
Tried Searching ForYour Code method and still could  
not find a working code.  
Clear the device key as follows: Press and hold SET until  
the LED (red light) blinks twice,then release.Next enter  
9 - 9 - 2.Then press the device key to be cleared twice.  
Now repeat the Searching ForYour Code method on  
page 9.  
PROBLEM:  
SOLUTION:  
CHL and CHM do not work for your RCA TV.  
Due to RCA design (1983-1987),only the original  
remote control will operate these functions.  
PROBLEM:  
SOLUTION:  
No remote control of volume.  
See ChangingVolume Lock on page 13 to lock/unlock  
volume.  
For additional information:  
15  
 
INSTRUCTIONS TO THE USER  
This equipment has been tested and found to comply with the limits for a class  
B digital device,pursuant to part 15 of the FCC Rules.These limits are designed  
to provide a reasonable protection against harmful interference in a residential  
installation.This equipment generates,uses,and can radiate radio frequency  
energy and if not installed and used in accordance with the instructions,may  
cause harmful interference to radio communications.However,there is no guar-  
antee that interference will not occur in a particular installation.If this equip-  
ment does cause harmful interference to radio or television reception,which can  
be determined by turning the equipment off and on,the user is encouraged to  
try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase separation between equipment and receiver.  
Connect equipment into an outlet or a circuit different from that to which the  
receiver is connected.  
Consult dealer or experienced radio/TV technician for help.  
LIMITED LIFETIME WARRANTY  
Audiovox Electronics Corporation (theCompany”) warrants to you the original  
retail purchaser of this product that should it,under normal use and conditions,be  
proven defective in material or workmanship during its lifetime while you own it,  
such defect(s) will be repaired or replaced (at the Company’s option) without charge  
for parts and repair labor.To obtain repair or replacement within the terms of this  
Warranty,the product is to be delivered with proof of warranty coverage (e.g.dated  
bill of sale),specification of defect(s),transportation prepaid,to the Company at the  
address shown below.ThisWarranty does not cover product purchased,serviced or  
used outside the United States or Canada.ThisWarranty is not transferable and does  
not extend to costs incurred for installation,removal or reinstallation of the product.  
ThisWarranty does not apply if in the Company’s opinion,the product has been  
damaged through alteration,improper installation,mishandling,misuse,neglect,  
accident,or the simultaneous use of different battery types (e.g.alkaline,standard or  
rechargeable).  
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THISWARRANTY IS  
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDEDABOVEAND,IN NO  
EVENT,SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE  
PAID BY PURCHASER FOR THE PRODUCT.  
ThisWarranty is in lieu of all other express warranties or liabilities.ANY IMPLIED  
WARRANTIES,INCLUDINGANY IMPLIEDWARRANTY OF MERCHANTABILITY  
OR FITNESS FORA PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION  
OF THISWARRANTY.IN NO CASE SHALL THE COMPANY BE LIABLE FORANY-  
CONSEQUENTIAL OR INCIDENTAL DAMAGESWHATSOEVER.No person or rep-  
resentative is authorized to assume for the Company any liability other than  
expressed herein in connection with the sale of this product.Some states/provinces  
do not allow limitations on how long an implied warranty lasts or the exclusion or  
limitation of incidental or consequential damage so the above limitations or exclu-  
sions may not apply to you.ThisWarranty gives you specific legal rights and you may  
also have other rights,which vary from state/province to state/province.U.S.A.:  
Audiovox Electronics Corporation,150 Marcus Blvd.,Hauppauge,NewYork 11788  
CANADA:Audiovox Return Center,c/o Genco,6685 Kennedy Road,Unit 3,Door 16,  
Mississauga,Ontario L5T 3A5  
URC-4021  
07/08  
16  
 
ADDITIONAL INFORMATION  
ONE FORALL® is the registered trademark of Universal Electronics Inc.  
AudiovoxAccessories Corporation is the Licensee of the ONE FORALL® brand  
for NorthAmerica.  
Copyright 2004 by Universal Electronics Inc.No part of this publication may be  
reproduced,transmitted,transcribed,stored in any retrieval system,or translated  
to any language,in any form or by any means,electronic,mechanical,magnetic,  
optical,manual,or otherwise,without the prior written permission of Universal  
Electronics Inc.  
The One ForAll® 4 Device Universal Remote Control is compatible for use in  
NorthAmerica,excluding Mexico.  
This One ForAll® 4 Device Universal Remote Control is covered by one or more  
of the following US Patents:  
6,587,067  
6,587,067  
6,496,135  
5,481,256  
5,515,052  
5,959,751  
17  
 
MANUFACTURER’S CODES  
[CÓDIGOS DEL FABRICANTE]  
Setup Codes for Cable Boxes  
[Códigos de configuración para cajas (convertidores) de cable]  
ABC  
0003,0008  
Pulsar  
0000  
Americast  
Bell South  
Digeo  
0899  
Quasar  
0000  
0899  
Runco  
0000  
1187  
ScientificAtlanta  
Starcom  
Supercable  
Torx  
0008,1877  
0003  
General Instrument 0003,0276  
Jerrold  
0003,0276  
0000  
0276  
Memorex  
Motorola  
Pace  
0003  
0276,1187,1376  
0008,1877  
0000  
Toshiba  
Zenith  
0000  
0000,0899  
Panasonic  
Paragon  
Pioneer  
0000  
0533,1877  
Setup Codes for Cable Box/PVR (or DVR) Combos  
[Códigos de configuración para equipo combinado de cable/PVR  
(o DVR)]  
Americast  
0899  
Pioneer  
1877  
1877  
0276  
0899  
Digeo  
1187  
ScientificAtlanta  
Supercable  
Zenith  
Motorola  
Pace  
1376,1187  
1877  
Setup Codes for DVD Players  
[Códigos de configuración para reproductores de DVD]  
Akai  
0695,0899  
KLH  
0717,0790,1020  
1127,1938  
0741  
Alco  
0790  
Lenoxx  
LG  
Apex Digital  
0672,0717,0755,0794,0796,  
0830,1020,1056,1061  
Magnavox  
0503,0539,0646,0675,0821,  
1268  
Audiovox  
0790  
0717  
0571  
0695  
Blaupunkt  
Blue Parade  
Broksonic  
Marantz  
Memorex  
Microsoft  
Mintek  
0539  
0695  
0522  
CaliforniaAudio Labs0490  
0717,1472  
0521,1521  
0741  
Denon  
0490  
Mitsubishi  
NAD  
DiamondVision  
Disney  
1316,1609,1610  
0675  
Nesa  
0717  
Durabrand  
DVD2000  
Emerson  
Funai  
1127  
NexxTech  
Norcent  
Onkyo  
1830  
0521  
1830  
0675,0821,1268  
0675,1268  
073  
0503,0627  
Panasonic  
0490,0503,0703,1362,1462,  
1490,1762  
Gateway  
GE  
Philips  
0503,0539,0646,0675  
0522,0717  
0741,0744,1044,1075  
0741  
Pioneer  
Polaroid  
PolkAudio  
Presidian  
Proceed  
Proscan  
RCA  
0525,0571  
1020,1061,1316  
0539  
GoVideo  
GoldStar  
Gradiente  
Greenhill  
Grundig  
Hitachi  
Hiteker  
iLo  
0490  
0675  
0717  
0672  
0539  
0522  
0573  
0522,0571,0717,0790,0822,  
1022,1132  
0672  
1348,1472  
0717,1472  
1830  
Regent  
Rotel  
1938  
0623  
Initial  
Insignia  
Integra  
Samsung  
0490,0573,0744,0820,0899,  
1044,1075  
0571,0627  
0558,0623,0867,1164  
0790  
JVC  
Sansui  
0695  
Kawasaki  
Kenwood  
continued on next page...  
continúa en la página siguiente...  
0490  
18  
 
MANUFACTURER’S CODES  
[CÓDIGOS DEL FABRICANTE]  
Setup Codes for DVD Players  
[Códigos de configuración para reproductores de DVD]  
Sanyo  
0695  
Technics  
Theta Digital  
Toshiba  
0490,0703  
0571  
Sharp  
0630,0675  
0533  
Shinsonic  
Sony  
0503,0695,1045,1154  
0503  
0533,0864,1033,1431  
0821  
Urban Concepts  
Venturer  
Xbox  
Superscan  
Sylvania  
Symphonic  
Teac  
0790  
0675,0821,1268  
0675,1268  
0790  
0522  
Yamaha  
0490,0539  
0503,0741  
Zenith  
Setup Codes For DVD Player/VCR Combos  
[Códigos de configuración para equipo combinado de DVD/VCRs]  
Apex Digital  
Broksonic  
Emerson  
Funai  
1061  
Polaroid  
Presidian  
RCA  
1061  
0695  
0675  
0675  
0522,0822  
0820,1044,1075  
0695  
0675  
Samsung  
Sansui  
GoVideo  
GoldStar  
JVC  
0741,0744,1044,1075  
0741  
Sharp  
0630  
0867,1164  
0741  
Sony  
0864,1033,1431  
0675  
LG  
Sylvania  
Symphonic  
Toshiba  
Zenith  
Memorex  
Panasonic  
Philips  
0695  
0675  
1762  
0503  
0675  
0741  
Setup Codes for PVRs (or DVRs)  
[Códigos de configuración para PVR (o DVR) (Videograbadoras  
Personales Digitales en Disco Duro)]  
Niveus Media  
Northgate  
Panasonic  
Philips  
1972  
ABS  
1972  
1972  
1972  
1972  
0739  
1972  
1972  
1972  
Alienware  
CyberPower  
Dell  
0616  
0618,0739  
0880  
RCA  
DirecTV  
Gateway  
Hewlett Packard  
ReplayTV  
Samsung  
Sonic Blue  
Sony  
0614,0616  
0739  
0614,0616  
0636,1972  
1972  
Howard Computers 1972  
HP  
1972  
Stack 9  
Hughes Network  
Systems  
0739  
0739  
1972  
1972  
1972  
1972  
1972  
1972  
Systemax  
Tagar Systems  
Tivo  
1972  
Humax  
1972  
Hush  
0618,0636,0739  
1008,1972  
1972  
iBUYPOWER  
Linksys  
Toshiba  
Touch  
Media Center PC  
Microsoft  
Mind  
Viewsonic  
Voodoo  
1972  
1972  
ZT Group  
1972  
Setup Codes for Satellite Receivers  
[Códigos de configuración para receptores de satélite]  
DirecTV  
1377,0099,0247,0392,0566,  
0639,0724,0749,0819,1076,  
1108,1142,1392,1442,1609,  
1639,1640,1749,1856  
Echostar  
Expressvu  
GE  
0775,1005,1505,1775  
0775,1775  
0392,0566  
General Instrument 0869  
Dish Network  
0775  
GOI  
0775,1775  
Dish Network  
System  
Hisense  
Hitachi  
1535  
0819  
0775,