Universal Remote Control Universal Remote UR J550TVE User Manual

STEP3 Point the remote control toward  
the TV and enter the three-digit  
code from the code table. If  
there is more than one code  
number assigned to your TV  
brand, try one code number at a  
time until the TV turns off right  
after you entered the number.  
*Tip: Red light will blink twice  
Operating Manual  
for 2 in 1 Cable TV  
Remote Control  
This remote control is preprogrammed  
to operate CABLE Box.  
The [  
] button sends out the TV  
and CABLE power commands if you  
Please program it for your TV by  
following the instructions shown below.  
press the [  
] button.  
To return to the original function, press  
the [CH-] button in the STEP2 .  
B. Recalling the TV Three-digit code :  
The remote control uses AAA batteries.  
Please be sure to match the batteries  
Searching Method  
STEP1 Press [TV POWER] and [MUTE]  
buttons simultaneously until the  
red light is on.  
Press [CH +] button and hold until the  
TV turns off. As soon as the TV turns  
off, release [CH+] button.  
with the ( ) and ( ) markings inside the  
battery compartment during installation.  
STEP2 Press [VOLUME-] button.  
*Tip : You can confirm the power off and  
The red light will blink a number of  
times indicating the number of each  
digit of the code. Each digit is  
separated by one second interval of  
red light being off.  
on by pressing [MUTE] button.  
STEP4 Press [TV POWER] button to  
store the three-digit code.  
Install two AAA alkaline  
batteries as shown here  
*Tip: Red light will blink twice.  
*Tip: One blink, three blinks and 10  
blinks, indicates the code  
number 130.  
Three-digit code :  
Set-up for your VOLUME control  
The remote control is preprogrammed to Helpful hints  
Press arrow gently &  
pull down to remove cover  
control VOLUME and MUTE functions  
Set-up for your Cable Box  
through your TV. To switch VOLUME and  
MUTE functions to your Cable Box:  
The remote control is preprogrammed  
to control your cable box. If it does  
not work properly, please set-up the  
right code by using the three-digit  
code or searching method.  
STEP1 Press [  
] and [MUTE]  
Programming your remote control  
Setup for your cable box  
buttons simultaneously until  
red light is on.  
No setup is required. The remote control is  
preprogrammed to operate your cable box.  
If you have a TV with a remote  
control, we recommend that you plug  
its power cord directly into a wall  
outlet if available (your cable installer  
may select an alternate setup)  
STEP2 Press [VOLUME +] button.  
STEP3 Press [  
] button.  
Setup for your TV  
To return to the TV’s VOLUME, press  
[TV POWER] button.  
Find your TV brand and its three-digit  
code on the back of this manual. If the  
TV brand is not listed, please use the  
Searching Method in STEP3 .  
*Tip: Red light will blink twice.  
If red light does not blink when  
you press keys the operation is  
Set-up for advanced functions  
STEP1 Turn on your TV manually.  
A. To turn on your TV and Cable at the  
same time with  
*Tip : If you have RCA TV, dont turn  
Make sure the batteries are inserted  
Replace old batteries with two new  
AAA batteries. Please do not mix old  
batteries with new ones.  
on the TV.  
STEP1 Press [  
] and [0] buttons  
simultaneously until the red  
light is on.  
Universal Remote Control, Inc.  
STEP2 Press [TV POWER] and [MUTE]  
buttons simultaneously until the  
red light is on.  
OEE-0017D Rev 03(05/14/02)  
STEP2 Press [CH +] button.  

Teac Fryer HD63G Series User Manual
Tektronix Printer Accessories 016 1318 00 User Manual
Teledex Conference Phone B250D User Manual
Toastmaster Toaster T2055BC User Manual
Toshiba Telephone CTX User Manual
Toshiba Two Way Radio MMU AP0091H User Manual
Tyan Computer Computer Monitor tgm 300 User Manual
ViewSonic Flat Panel Television VT2730 User Manual
Vinotemp Refrigerator 250SCU User Manual
Vizio Flat Panel Television D650i C3 User Manual