Universal Remote Control Universal Remote MX700 User Manual

GUIDE TO  
SIMPLE  
HOME  
THEATER  
OPERATION  
WITH YOUR  
HOME THEATER MASTER  
REMOTE CONTROLS  
 
1
2
Finding the MAIN Menu  
Turn On Your Entire System  
The MAIN Button always takes you to  
the MAIN Menu.  
Power on/off your entire system  
with the MAIN Menu by following  
these steps:  
1. Touch the MAIN button to make  
sure that you are on the MAIN Menu.  
It doesn’t matter which page of the  
MAIN Menu is displayed.  
The PAGE button switches between  
two MAIN Menu pages IF you have  
more than ten remote controls.  
When the top title bar says MAIN, you  
are on the MAIN Menu.  
2. Point the Home Theater Master at  
the system (usually a repeating sensor  
near the screen).  
3. Touch the On or Off button as  
desired. Hold the remote steady and  
pointed at the system until all compo-  
nents are correctly powered on or off.  
Turning on the system may take ten to  
twenty seconds.  
PAGE 1  
The lower title bar displays PAGE 1 or  
PAGE 2 as you switch. Each of the  
remote controls are represented by a  
button next to the corresponding  
screen label.  
4. If one component does not turn  
on/off, simply touch the button again.  
TIP Hold the remote control  
steady and pointed at the sys-  
tem until the  
indicator  
stops flashing.  
 
 
3
4
Hold the remote  
Using the MAIN Menu  
The MAIN Menu enables you to either  
select a new Activity or simply select a  
new Device to control.  
When you select a new activity, the  
Home Theater Master will issue a  
MACRO (a timed sequence of many  
commands from many different remote  
controls). This MACRO was custom  
programmed for your system by your  
installer. It will issue all of the com-  
mands necessary to switch the sound  
and picture of your system.  
The MAIN Menu buttons issue  
MACROS that reset the sound and  
picture of your home theater to a new  
activity.  
TIP Hold the remote control  
steady and pointed at the sys-  
tem until the  
stops flashing.  
indicator  
When you select a device, the Home  
Theater Master becomes the remote  
control you select WITHOUT affecting  
the home theater.  
If the sound or the picture still are  
not correct, repeat steps 1 - 4.  
Select a New ACTIVITY  
Select a DEVICE Only  
1. Touch the MAIN button to make  
sure that you are on the MAIN  
Menu. Touch the PAGE button if you  
don’t see the activity you want.  
1. Touch the MAIN button to make  
sure that you are on the MAIN  
Menu. Touch the Page button if you  
don’t see the activity you want.  
2. Press and hold the MAIN button.  
While holding the MAIN button  
down, touch the button next to the  
desired screen label. The remote  
control will now display the name of  
the selected device and all buttons  
will operate the device, however, the  
sound and the picture of your sys-  
tem have not been changed.  
2. Point the Home Theater Master at  
the system (or at the repeating  
INFRARED sensor if one is  
installed).  
3. Touch the activity button next to  
the desired screen label. For exam-  
ple if you wish to watch a DVD  
movie, touch the DVD button.  
 
 
5
6
The Power ON and OFF buttons now  
operate only the selected device (to  
turn the entire system on/off, return to  
the MAIN Menu).  
Controlling the Volume  
For your convenience, the VOLUME  
Up, VOLUME Down and the MUTE  
buttons will always control the sur-  
round sound system, regardless of  
what activity or device you are control-  
ling.  
The ten screen labeled buttons are  
now labeled with any commands  
that do not fit one of the buttons with  
printed labels.  
Operating any Device  
You can see the name of the device at  
the top of the screen. If it is not the  
one you want, return to the MAIN  
Menu and select a new device or  
activity.  
Up to 40 screen labeled buttons are  
available for each device. To view  
the additional buttons, press the  
PAGE button to display additional  
pages. The Home Theater Master  
can display up to four pages of  
screen labeled buttons for each  
activity or device! As you scroll  
through the pages, notice that the  
bottom title bar displays which page  
you are viewing (PAGE 1, PAGE 2,  
etc.).  
All of the printed  
label buttons on the  
remote operate just  
like the original  
remote control (with  
the exception of  
Volume Up, Volume  
Down and Mute  
which operate your  
surround sound sys-  
tem).